ArbNation Join free

Measuring tree height: clinometers, laser hypsometers and the stick method

Foresters measure tree height with a clinometer and tape, a height meter, a laser rangefinder or a stick. A USDA Forest Service paper, NSW EPA, UBC and WSU Extension set out the maths and the pitfalls.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

The UBC BC BigTree site calls height the hardest measurement to take accurately, especially for larger trees. It lists three pieces of equipment: a measuring tape, a calculator with cosine and tangent functions, and an inclinometer. A hypsometer measures distance and angles and calculates height in one tool, and smartphone apps can stand in as an inclinometer.

The tangent method with a clinometer

UBC gives the level-ground rule as height equals the tangent of the angle to the treetop times the distance from the tree, plus the eye height. On a slope where the base is above or below eye level, a second angle to the base is measured. Angles are added when the observer is above the tree and subtracted when below. Beyond a ground slope of 6 degrees (10 percent), UBC says slope distance has to be measured instead.

The NSW Environment Protection Authority guideline on stand height uses the percent scale of a clinometer. Its worked example reads 50 percent at 38 metres, which gives 19 metres, and adds 1.6 metres of eye height for about 20.6 metres. For sloping ground it adds the base reading when the base is below eye level and subtracts it when above. A reading of 50 percent at the top and 13 percent at the base, at 38 metres, gives 23.9 metres.

WSU Extension's inventory cheat sheet describes the same arithmetic in feet. A clinometer reading of +90 percent to the top and -5 percent to the base, from 100 feet away, combines to 95 percent and a height of 95 feet.

Other methods in the sources

MethodDescribed byWhat the source says about it
Tape held at arm's lengthNSW EPAThe cheapest and simplest technique, with two people. A mark at 10 percent of the apparent height gives 10 percent of the true height. It needs no measured distance from the tree, and slope does not matter
Clinometer, degree scaleNSW EPACorrects the observed height by the cosine of the ground slope, or corrects the distance the same way. A reading of 23.9 metres on a 9 degree slope becomes 23.6 metres
Height meterNSW EPARead from a fixed distance of 15 or 20 metres. Readings are doubled at 30 and 40 metres
Electronic clinometerNSW EPAListed as a fifth method in the same guideline
Woodland stickWSU ExtensionHeld vertically 25 inches from the eye, from a prescribed distance of usually 66 or 100 feet depending on the stick
Stick of arm lengthUBCWorks only on level ground. The distance from the observer's feet to the tree is roughly the tree's height

The NSW guideline sets stand height as the average height of five dominant trees in the stand.

Lean, wide crowns and the sine method

Don Bragg of the USDA Forest Service wrote in the Journal of Forestry that the similar triangles and tangent methods have dominated height measurement because they are easy and need only simple technology. They rest on assumptions that are only sometimes met in the field. Tree lean and irregular crowns are the hard cases.

For a leaning tree, the tangent method overestimates height if the tree leans toward the observer and underestimates it if the tree leans away. Chapman, quoted in the paper, noted that the error for broad-crowned trees tends to overestimate height. UBC says a strongly leaning tree is measured with the lean to the left or right, not toward or away from the observer. It also calls for a second attempt from another viewpoint in difficult stands.

Bragg describes the sine method, developed from Grosenbaugh's work, as the alternative. It uses the slope distance and angle to the top and to the base. Because it measures slope distances directly, it gives the right height whatever the lean, ground slope or distance from the stem. Modern laser rangefinders that include the method can scan several apparent high points from one spot to find the true top. On a vertical tree on level ground, the sine and tangent methods give the same height.

Sources