ArbNation Join free

Moisture meters for firewood: what EPA, GOV.UK, Forest Research and Oregon State say

EPA and the English government's wood-sale notice both point to a moisture meter, with 20 percent as the line. GOV.UK's notice mentions calibrating the meter and a freshly split surface. Oregon State describes pin and non-penetrating meters.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The meter statements here come from EPA's Burn Wise pages, two GOV.UK pages from the Department for Environment, Food and Rural Affairs, Forest Research and Oregon State University Extension. The Burn Wise pages are a historic record that EPA stopped updating on October 30, 2025.

Meter statements by source

What each source prints about measuring moisture
SourcePrinted statement
EPA Burn WiseWood burns best below 20 percent moisture content. Wood is tested with a wood moisture meter before burning
GOV.UK, selling wood in EnglandReady to Burn wood has a moisture content of 20 percent or less. Wood sold in volumes of 2 cubic metres or more comes with a customer notice on drying, storing and checking moisture
GOV.UK, customer noticeThe notice tells buyers to test wood, ideally with a moisture meter, calibrated first, on a freshly split surface
Forest ResearchMoisture content matters for boilers, stoves and the energy in a load of fuel. A spreadsheet converts between dry basis and wet basis
Oregon State Extension, EM 8612Resistance meters have pins that penetrate the wood. Dielectric meters have smooth surfaces. Accuracy is questionable above about 30 percent
Pin versus pinless on a split firewood faceNot stated in these sources

EPA Burn Wise

EPA's best wood-burning practices page puts the burn line at a moisture content of less than 20 percent. It tells readers to test wood with a wood moisture meter before they burn it. The page also links best-practices videos on testing wood with a moisture meter. EPA prints no meter type, reading position or accuracy figure.

GOV.UK guidance and customer notice

The Department for Environment, Food and Rural Affairs guidance on selling wood for domestic use in England sets the Ready to Burn scheme. Firewood and briquettes in volumes under 2 cubic metres must be certified as having a moisture content of 20 percent or less. Wood sold in volumes of 2 cubic metres or more needs no certification, but the supplier must give customers a notice on how to dry, store and check the moisture of the wood. The guidance says a seller can face a £300 fixed penalty from the local authority, or a larger court fine, for wood stored above 20 percent moisture content or sold without the Ready to Burn logo or correct labelling.

The notice is published as statutory guidance and is Crown copyright, available under the Open Government Licence v3.0. It reads that wood is not suitable for burning until dried and that it should not be burned until it has a moisture content of 20 percent or less. It adds that radial cracks and bark that comes off easily suggest wood that is ready for burning. The notice says to test the wood when it seems ready, ideally with a moisture meter. It says to calibrate the meter first and then measure a freshly split surface to get the best reading.

Forest Research on moisture content

Forest Research calls moisture content a critical parameter for woodfuel, central to the correct operation of boilers and stoves and to the calorific value of a load. Most woodfuel boilers operate on fuel within a limited moisture range. Fuel outside it makes the boiler run inefficiently, with higher emissions, or trips the control system. Moisture content decides how much energy a buyer pays for when buying by weight. It matters far less when buying by volume.

The page offers a spreadsheet giving net calorific value as a function of moisture content for typical hardwoods and softwoods. It also converts moisture content quoted on a dry basis to a wet basis. It does not describe meters.

Meter types and limits at Oregon State

Oregon State University Extension's EM 8612 is about lumber, not firewood. It describes the resistance, or conductance-type, meter as the most common hand-held type, with pins that penetrate the wood surface. The dielectric power loss meter is the other type, with smooth surfaces that do not penetrate the wood. Mills use dielectric meters in-line.

The publication says moisture meters are not as accurate as its sample board method. For moisture contents greater than the fiber saturation point, about 30 percent, meter accuracy is questionable. Both types need temperature and species corrections for accurate measurements, and manufacturers supply these.

Sources