ArbNation Join free

National Tree Climbing Guide chapters 5 and 6: tree entry, ladders and the four-inch tie-in

Chapter 5 of the US Forest Service National Tree Climbing Guide has six sections on tree entry. Chapter 6 sets the four-inch tie-in at 5,400 pounds, falls of no more than 6 feet above 4 inches, and lanyard use.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named codes and training bodies are described here as published. It is not training and does not teach the work.

Chapter 5 and 6 headings

The US Forest Service National Tree Climbing Guide, 2015 electronic edition, spends chapter 5 on tree entry methods and chapter 6 on working in the tree.

Sections of chapters 5 and 6
SectionHeadingPage
5.1Climbing Spurs44
5.2Ladders47
5.3Line Installation50
5.4Single Rope Technique (SRT)52
5.5Doubled Rope Technique (DRT)56
5.6Tree Steps58
6.1Three Point Climbing60
6.2Free Climbing60
6.3Four Inch Tie-In System61
6.4Lanyard Use63
6.5Handling Materials in Trees64

Spurs, ladders and tree steps

Section 5.1 calls spur climbing "typically the fastest and simplest way" into a crown, then warns that the gaffs can seriously injure the bole. Job, species, location and the value of the tree all weigh in. Spurs suit trees not prone to long-term trouble from puncture wounds, and five-needle pines are singled out to avoid. The guide names quick crown access in a rescue, when no other system is in place, as an especially suitable use. Standard spur equipment includes two lanyards.

Section 5.2 names the Swedish sectional tree climbing ladder, or an equivalent design, as the type most suitable. Other stacking ladders are less secure. Metal ladders should carry electrical hazard warning labels. The procedures bar climbing wet, icy or snow-covered ladders and leaving ladders unattended in trees. A lanyard is used while unsecured ladders are erected and climbed.

Section 5.6 describes tree steps as lightweight metal platforms on a chain. A lanyard must be used at all times when tree steps give support. Steps sit no more than 24 inches apart on one side of the bole, or 12 inches apart when staggered. Inspection for metal fatigue is called the most critical maintenance item.

Three-point climbing, free climbing and the four-inch limit

Section 6.1 holds that three points of contact are firmly placed before the climber moves another. A lanyard secured at both ends around the bole counts as two points. Rappelling and approved ascender systems, DRT friction hitch climbing included, are the exceptions. Both hands or both feet are never placed on a single sound live branch under 3 inches in diameter.

Free climbing, section 6.2, is climbing without a safety line or lanyard. It is limited to the area below the 4-inch bole diameter level, and it also covers going up and down a secured ladder. The guide advises against it in trees with steeply down-sloping branches.

The four-inch tie-in

Section 6.3 defines the 4-inch tie-in as a self-belayed rope system required when climbing and working above the 4-inch bole diameter. The guide adds that it can be time consuming to set up and take down, and can hinder a quick descent in an emergency. Five requirements are stated.

  • The system is secured to the bole at or below the 4-inch bole diameter.
  • Above that level, protection (a rigging point) goes in at least every 3 feet along the bole, so falls stay at 6 feet or less.
  • It is built with dynamic rope, because static rope puts a high impact force on the anchor points and the climber.
  • The friction hitch or belay device is tested on the ground.
  • Each part meets or exceeds a 5,400-pound breaking strength standard.

The guide gives a typical belay rope length of about 30 feet for conifers. It calls anchoring anywhere from 4 to 12 inches of bole diameter common.

Lanyard use

Section 6.4 has three parts: throwing and catching the lanyard (6.4.1), the limb-over technique (6.4.2) and lanyard adjustment (6.4.3). The glossary calls the steel-core lanyard recommended for spur climbing and required when cutting, trimming or pruning in a tree. The limb-over technique uses a second lanyard, so two are standard.

OSHA and the UK code on ladders

OSHA 1910.23 is the general-industry ladder rule. Rungs are spaced 10 to 14 inches apart. Ladders are inspected before initial use in each work shift, and a defective one is tagged "Dangerous: Do Not Use". The climber faces the ladder and grasps it with at least one hand. Ladder sections are not tied or fastened together for added length unless designed for such use.

The Arboricultural Association's Industry Code of Practice for Arboriculture: Tree Work at Height restricts ladders to low risk, short duration tasks in both editions. Section 2.8.2 of Edition 1 (February 2015) gives lower canopy access for a staged ascent and short hedge trimming as examples. Section 3.8.2 of Edition 2 (May 2020) adds "typically less than 30 minutes in duration". Both editions call for another work method when the task needs extended time on a ladder. Neither edition uses the term four-inch tie-in.

Edition 2 section 3.8.7 treats spurs as invasive, to be used only where tree health is of negligible consequence, such as a removal or an aerial rescue. It adds that spiking must be used with a personal fall protection system. Section 3.10.6.10 prefers an adjustable lanyard for its ability to minimise slack and sets a minimum breaking strength of 15 kN.

The rest of the guide is outlined in the guide to the National Tree Climbing Guide.

Sources