New-worker training duties: United States
OSHA's logging standard, 1910.266, requires training before a new employee's first assignment and close supervision afterwards. The line-clearance standard, 1910.269, adds retraining triggers, and the General Duty Clause sits behind both.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The sources are two federal OSHA standards, 29 CFR 1910.266 and 29 CFR 1910.269, and section 5 of the Occupational Safety and Health Act. State plans and the ANSI Z133 standard are not covered. For the record an employer can keep, see the guide to training record fields.
At a glance
| Provision | Covers |
|---|---|
| 29 CFR 1910.266(i) | Logging operations |
| 29 CFR 1910.269(a)(2) | Electric power work, including line-clearance tree trimming |
| OSH Act section 5 | Every employer: the General Duty Clause and compliance with standards |
Logging operations: 1910.266(i)
Section 1910.266 applies to all logging operations. The standard defines them as operations associated with felling and moving trees and logs from the stump to the point of delivery. Its list includes marking danger trees, felling, limbing, bucking, debarking, chipping, yarding, loading, unloading and storing.
Paragraph (i)(1) says the employer shall provide training for each employee, including supervisors, at no cost to the employee. Under (i)(2), training is given:
- as soon as possible, and not later than the standard's effective date, for initial training of each current and new employee;
- before initial assignment for each new employee;
- whenever the employee is assigned new work tasks, tools, equipment, machines or vehicles;
- whenever an employee demonstrates unsafe job performance.
The minimum content, in (i)(3), is six elements:
- Safe performance of assigned work tasks.
- Safe use, operation and maintenance of the tools, machines and vehicles the employee uses, with emphasis on the manufacturer's instructions, warnings and precautions.
- Recognition of safety and health hazards tied to the employee's specific tasks, and the measures and work practices that prevent or control them.
- Recognition, prevention and control of other hazards in the logging industry.
- Procedures, practices and requirements of the employer's work site.
- The requirements of the standard.
Paragraph (i)(4) allows retraining after unsafe performance or a new task to be limited to the relevant elements. Under (i)(5), an employee already trained in particular elements need not be retrained in them, and the employer trains in the elements not yet covered. The employer is responsible for seeing that each employee can properly and safely perform the tasks and operate the tools and machines used.
Paragraph (i)(6) requires each new employee to work under the close supervision of a designated person until the employee demonstrates the ability to perform the new duties safely and independently. Other paragraphs add:
- First-aid and CPR training that meets appendix B and stays current, under (i)(7).
- Training conducted by a designated person, under (i)(8).
- Training presented in a manner the employee is able to understand, with materials suited to the educational level, literacy and language skills of the employees, under (i)(9).
- A written certification record holding the employee's name or identity, the dates of training, and the signature of the trainer or the employer, under (i)(10). Where the employer relies on earlier training, the record shows the date the employer judged it adequate. The most recent certification is maintained.
- Safety and health meetings at least each month for each employee, under (i)(11).
Line-clearance tree trimming: 1910.269(a)(2)
Section 1910.269 reaches line-clearance tree trimming done to clear space around electric power lines or equipment, on behalf of the organization that operates or controls them. The whole section, except paragraph (r)(1), applies when the work is done by qualified employees. Paragraphs (a)(2), (a)(3), (b), (c), (g), (k), (p) and (r) apply when it is done by line-clearance tree trimmers who are not qualified employees.
Under (a)(2)(i), every employee covered is trained in, and familiar with, the safety-related work practices and procedures that pertain to the job assignment. Each employee is also trained in other safety practices related to the work, including applicable emergency procedures such as pole-top and manhole rescue. The degree of training is determined by the risk to the employee for the hazard involved.
A line-clearance tree trimmer who is not a qualified employee is also trained and competent in three skills, under (a)(2)(iii):
- distinguishing exposed live parts from other parts of electric equipment;
- determining the nominal voltage of exposed live parts;
- the minimum approach distances for the voltages the employee will meet, and keeping them.
Paragraph (a)(2)(iv) has the employer determine, through regular supervision and inspections at least annually, that each employee follows the work practices. Additional training or retraining follows under (a)(2)(v) if supervision or inspection shows non-compliance, if new technology, equipment or procedures call for different practices, or if the employee must use practices not normally used in regular duties. A note to (a)(2)(v)(C) records that OSHA considers tasks performed less often than once per year to need retraining first.
Training is classroom or on-the-job under (a)(2)(vi). Under (a)(2)(vii) and (viii), it establishes proficiency in the work practices, and each employee must demonstrate proficiency to the employer before the training counts as complete. The first-aid rule in (b)(1)(i) asks for two trained persons on field work by two or more employees on or near exposed lines or equipment energized at 50 volts or more. For line-clearance tree trimmers who are not qualified employees, one trained person is enough if all new employees are trained in first aid within 3 months of their hiring dates.
OSH Act section 5
Section 5(a) of the Occupational Safety and Health Act (29 USC 654) says each employer shall furnish each employee employment and a place of employment free from recognized hazards. These are hazards that are causing or are likely to cause death or serious physical harm. Each employer shall also comply with the occupational safety and health standards promulgated under the Act. Section 5(b) says each employee shall comply with the standards, rules, regulations and orders that apply to his or her own actions and conduct.
Sources
- OSHA, 29 CFR 1910.266, Logging operations, paragraph (i) Training, read October 19, 2026
- OSHA, 29 CFR 1910.269, Electric power generation, transmission, and distribution, paragraph (a)(2) Training, read October 19, 2026
- OSHA, Occupational Safety and Health Act of 1970, section 5, Duties, read October 19, 2026