Notch, hinge and back cut names in the codes: scarf, sink cut, undercut, holding wood
The codes name the same felling cuts differently. British Columbia says undercut and holding wood, New South Wales and New Zealand say scarf and back cut, and HSE and the Irish guides say sink cut and felling cut.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work.
Names by source
| Source | Notch and back cut | Uncut wood |
|---|---|---|
| WorkSafeBC | Undercut, backcut | Holding wood |
| SafeWork NSW | Scarf, back cut | Holding wood |
| WorkSafe NZ | Scarf, back cut | Hinge |
| HSE case studies | Sink cut, felling cut | Hinge |
| HSE chainsaws | Sink cut, main felling or back cut | Hinge |
| IFSG 302 | Sink cut, main felling cut | Hinge |
British Columbia
WorkSafeBC defines holding wood in section 26.1 as the hinge of wood left uncut between the back of the undercut and the backcut. Section 26.24 then sets the felling procedure: a sufficient undercut, complete and cleaned out; sufficient holding wood; and a backcut higher than the undercut to provide a step on the stump. The regulation does not define undercut or backcut separately.
New South Wales
The SafeWork NSW code, which commenced on 27 March 2026, defines the scarf as two cuts made to form a notch, which determines the direction of fall when felling or topping, or the direction of break when removing a branch. It defines the back cut as the final release cut on the opposite side of the trunk from the scarf. The code is licensed under Creative Commons Attribution 4.0 and says a scarf and back cut should be used in felling trees. Figure 7 labels a 45 degree scarf, the holding wood, a step, and a back cut slightly above the scarf horizontal, with a note not to cut off corners.
New Zealand
Section 3.4.3 of the WorkSafe New Zealand code lists the accepted felling methods. The scarf cuts used shall be conventional, open-face or Humboldt, and should be 45 degrees or greater. The two cuts that form the scarf shall not cross where they meet. Scarf depth should not exceed one-third of the tree diameter, and the back cut shall not penetrate the predetermined hinge area. Figure 3 labels the scarf, the hingewood and the backcut.
Great Britain
HSE's terms list defines a sink cut as a triangular cut near the base of the trunk on the side the tree is meant to fall, at an angle of approximately 45 degrees. A felling cut is the horizontal cut into the rear of the tree, just above and towards the sink cut. It should stop before it meets the sink cut to create a hinge, the portion of the tree not cut through. HSE says the hinge allows the felling direction and the rate of fall to be controlled. On its chainsaws page HSE adds that control comes from an appropriate combination of directional or sink cut, hinge and main felling or back cut. FISA Safety Guide 302, updated June 2018, calls for an appropriately sized parallel sided hinge at right angles to the direction of fall and gives no size.
Ireland
IFSG 302, a guide modified for Irish use by kind permission of the Forest Industry Safety Accord, uses sink cut and main felling cut. The top and bottom sink cuts should meet exactly, with no over-cutting that could weaken the hinge. The main felling cut goes at or slightly above the level of the bottom sink cut. The guide leaves a parallel-sided hinge not less than 25 mm thick at right angles to the direction of fall.
Sources
- WorkSafeBC, Occupational Health and Safety Regulation, Part 26 Forestry Operations, sections 26.1 and 26.24, read October 16, 2026
- SafeWork NSW, Tree works code of practice, March 2026, read October 16, 2026
- WorkSafe New Zealand, approved code of practice for safety and health in arboriculture, section 3.4.3, read October 16, 2026
- Health and Safety Authority and Teagasc, Irish Forestry Safety Guide IFSG 302 Basic Chainsaw Felling and Manual Takedown, October 2018, read October 16, 2026
- Health and Safety Executive, Case studies: Treework accidents, terms and practices, read October 16, 2026
- Health and Safety Executive, Working with chainsaws, read October 16, 2026
- Forest Industry Safety Accord, FISA Safety Guide 302 Basic chainsaw felling and manual takedown, updated June 2018, read October 19, 2026