ArbNation Join free

Nursery stock names: standard, select standard, heavy standard and advanced nursery stock

UK nursery trees are graded by girth at 1 m: standard at 8 to 10 cm up to extra heavy standard at 14 to 16 cm. US stock is sized by caliper, height and root ball under ANSI Z60.2.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The UK stock grades below come from a Staffordshire County Council tree planting specification. The US sizes come from Penn State Extension, which cites the nursery stock standards of the American Nursery and Landscape Association.

The two standards

BSI lists BS 3936-1:1992, Nursery stock: Specification for trees and shrubs, as current, published January 31, 1992. It covers dimensions, containers and labelling for trees and shrubs, including conifers and woody climbing plants, that suit transplanting as ornamental or amenity plants but not timber production. It includes requirements for compost in a container and for labelling. It does not apply to roses, poplars or willows. BSI defines a tree in nursery stock as a woody perennial with a distinct stem or stems. The standard gives dimensions for seedlings, cuttings, transplants, whips, feathered trees and standard trees.

AmericanHort publishes the American Standard for Nursery Stock, ANSI Z60.2, approved April 12, 2025. It sets common terminology for measuring plants and for stating their size. The standard also covers the proper relationship between height and caliper, or height and width, and whether a root ball or container is large enough for a plant. It replaced ANSI Z60.1, approved in April 2014. The association dates its first Horticultural Standards to 1923.

UK grades in the Staffordshire specification

Staffordshire specifies trees by girth, the stem circumference measured 1 m above ground. Its table gives the dimensions that trees supplied to a specified size usually meet.

DesignationGirth at 1 mTotal height
Standard8 to 10 cm2.5 to 3.0 m
Select standard10 to 12 cm3.0 to 3.5 m
Heavy standard12 to 14 cm3.5 to 4.0 m
Extra heavy standard14 to 16 cm4.0 to 4.5 m
Advanced nursery stock16 to 18 cm4.0 to 4.5 m
Advanced nursery stock18 to 20 cm4.5 to 5.0 m
Semi-mature20 to 25 cm5.0 to 5.5 m
Semi-mature25 to 30 cm5.5 to 6.0 m
Semi-mature30 to 35 cm6.0 to 6.5 m
Super semi-mature40 to 45 cm7.0 m and over

The council table has no row between 35 and 40 cm. Semi-mature trees progress in 5 cm steps from 20 cm. Conifers and multi-stemmed trees are usually specified by total height in 50 cm steps, such as 250 to 300 cm, and are supplied feathered, with lateral branches to just above ground level. A conifer wanted as a clear-stemmed tree is specified by girth like a standard tree.

Staffordshire holds that smaller planting sizes will as a rule establish better than larger ones. A Select Standard gives a balance between a small tree and initial impact in a new scheme. In a paved town centre, larger sizes may be more appropriate, and they can resist vandalism better, since they are harder to snap. The specification also gives the approximate minimum tree pit sizes it usually expects, by grade.

GradePit diameterPit depth
Feathered450 x 450 mm300 mm
Standard and select standard (up to 10 to 12 cm girth)500 x 500 mm400 mm
Heavy standard600 x 600 mm500 mm
Extra heavy standard700 x 700 mm500 mm

US sizes in Penn State's guide

Penn State sizes trees by caliper, the trunk diameter. Caliper is measured 6 inches above the ground for trees up to 4 inches, and 12 inches above the ground for larger trees. It gives these minimum ball sizes.

Trunk caliperMinimum root ball diameterTree height
1 1/2 inches20 inches10 to 13 feet
2 inches24 inches12 to 15 feet
3 inches32 inches13 to 18 feet

Sources