ArbNation Join free

OSHA 1910.266 logging standard and tree crews: scope, key parts and the 1998 letters

Standard 1910.266 covers all types of logging, and a March 1998 OSHA letter said that reaches commercial tree trimming. OSHA withdrew the letter in June 1998 and paused 1910.266 citations to tree service employers (SIC 0783) not logging.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The standard is 29 CFR 1910.266, Logging operations, in Subpart R, Special Industries. The text was last amended in the Federal Register on July 1, 2014. The guide to OSHA standards for tree work covers the wider set of rules.

Scope in the standard

Paragraph (b)(1) says the standard "establishes safety practices, means, methods and operations for all types of logging," whatever the end use of the wood. Paragraph (b)(2) applies it to all logging operations as the section defines them. Hazards it does not address fall to other sections of part 1910 under (b)(3). The standard does not cover the construction or use of cable yarding systems.

Paragraph (c) defines logging operations as operations associated with felling and moving trees and logs from the stump to the point of delivery. The list includes marking, felling, bucking, limbing, debarking and chipping. It also names yarding, loading, unloading, storing and transporting machines, equipment and personnel, "but not limited to." A danger tree is a standing tree that presents a hazard because of deterioration, root or stem damage, or its direction and lean.

The two 1998 documents

On March 4, 1998, OSHA's Directorate of Compliance Programs answered the National Arborist Association in a letter sent to field offices. It states that the definition is broad enough to include commercial tree cutting and trimming. OSHA gives these reasons:

  • The listed operations include felling, cutting branches off trees and logs, and chipping.
  • Only the building and use of cable yarding systems are exempt, and tree cutting before a yarding system is used stays covered.
  • Leg protection exceptions for climbers and bucket trucks, and the overhead electric line provisions, are aimed at tree trimming.

The July 1, 1998 enforcement memorandum for regional administrators reports that OSHA withdrew that response on June 22, 1998, to talk again with the Association. Until those talks produced a result, citations under 1910.266 "shall not be issued" to employers in SIC 0783 (Ornamental Shrub and Tree Services) who are not engaged in logging operations. Any proposed citation had to be approved by the Director of Enforcement Programs. The memorandum is marked corrected April 14, 2005.

Parts of the standard that match tree-crew work

ParagraphWhat the text provides
(d)(1) Personal protective equipmentCut-resistant leg protection from thigh to boot top for chain saw operators, with an exception for climbers where a greater hazard is shown, and for work from a vehicle-mounted platform that meets 1910.67. Head, eye and face protection; face protection where a chipper is operated
(d)(2) First-aid kitsAt each work site where trees are being cut, at each active landing and on each employee transport vehicle
(d)(8) Overhead electric linesWork near lines follows 29 CFR 1910.333(c)(3). The power company is notified at once if a felled tree touches a line, and employees stay clear until it advises there are no electrical hazards
(e)(2) Chain sawsChain brake and ANSI B175.1-1991 for saws placed in service after the effective date. Continuous pressure throttle. Fuelled at least 10 feet (3 m) from any open flame and started at least 10 feet (3 m) from the fuelling area. Drop starting prohibited. No cutting directly overhead
(h)(2) Manual fellingA planned and cleared retreat path, an evaluation of snow, ice, wind, lean and dead limbs, an undercut, and a backcut that leaves hinge wood
(h)(4) Chipping (in-woods)Access covers shut until the drum or disc stops, guarded infeed and discharge ports, lockout for servicing
(i) TrainingTraining for each employee, including supervisors, at no cost to the employee, before first assignment and whenever tasks, tools or machines change or unsafe performance is shown

The training paragraph lists six content elements, from safe performance of assigned tasks and tools to the employer's work site procedures and the requirements of the standard. Appendices A and B set minimum first-aid supplies and first-aid training.

Sources