ArbNation Join free

OSHA hazard communication, respirator and silica standards and wood dust

Three federal standards reach airborne dust and chemicals: 29 CFR 1910.1200, 1910.134 and 1910.1053. Wood that is sawed or cut and gives off dust is not exempt from hazard communication, and the silica limit is 50 micrograms per cubic metre.

Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. OSHA's wood dust page says wood dust becomes a potential health problem when particles from processes such as sanding and cutting become airborne, and that breathing them may cause allergic respiratory symptoms, mucosal and non-allergic respiratory symptoms, and cancer. The extent of these hazards and the associated wood types have not been clearly established. The health side is on the wood dust guide.

The three standards side by side

StandardWhat it covers
29 CFR 1910.1200, hazard communicationClassifying chemical hazards and passing the information to workers through a written program, labels, safety data sheets and training
29 CFR 1910.134, respiratory protectionRespirator provision, a written program, selection, medical evaluation, fit testing and training
29 CFR 1910.1053, respirable crystalline silicaGeneral industry exposure limit, exposure assessment, regulated areas, controls, medical surveillance

OSHA's wood dust page says exposures to wood dust are addressed in specific OSHA standards for general industry. It also points to the Combustible Dust National Emphasis Program, directive CPL 03-00-008 of March 11, 2008.

Hazard communication, 29 CFR 1910.1200

Paragraph (b)(1) says the section requires chemical makers and importers to classify the hazards of what they produce. It requires all employers to give workers information about the hazardous chemicals they are exposed to, through a hazard communication program, labels, safety data sheets, and information and training. An employer that does not make or import chemicals needs only the parts on the workplace program and on passing information to workers. The section applies to any chemical known to be present where employees may be exposed under normal use or in a foreseeable emergency.

The definitions pull dust into the standard. Combustible dust means finely divided solid particles that pose a flash-fire or explosion hazard when dispersed in air. A hazardous chemical includes a combustible dust.

Paragraph (b)(6)(iv) carves out wood. Wood or wood products, including lumber that will not be processed, fall outside the section where the maker or importer can show the only hazard is flammability or combustibility. The paragraph states that wood treated with a covered hazardous chemical is not exempt, and neither is wood that may later be sawed or cut, generating dust.

  • Written program (e): kept at each workplace, with a list of the hazardous chemicals known to be present and how labels, data sheets and training will be handled.
  • Safety data sheets (g): the employer has a data sheet in the workplace for each hazardous chemical it uses.
  • Training (h): given at the time of initial assignment, and again whenever a new chemical hazard that workers have not been trained on is introduced into their work area.
  • Labels: paragraph (b)(5) lists chemicals the section does not require labelled, among them a pesticide that carries the labelling required under the federal pesticide law.

Respiratory protection, 29 CFR 1910.134

Paragraph (a)(1) sets the primary objective: prevent contamination of the air by accepted engineering controls such as enclosure, ventilation and substitution of less toxic materials. Where those controls are not feasible, or while they are being put in place, appropriate respirators are to be used. Paragraph (a)(2) puts the duty on the employer to provide a respirator to each employee when one is necessary to protect health, and to run a respiratory protection program.

ParagraphSubject
(c)A written program with worksite-specific procedures, run by a suitably trained program administrator
(d)Selection based on an evaluation of the respiratory hazards and of the workplace and user factors
(e)Medical evaluation, because a respirator can place a physiological burden on the wearer
(f)Fit testing of tight-fitting facepieces with the same make, model, style and size that will be used
(k)Training that recurs annually, and more often if necessary

Respirable crystalline silica, 29 CFR 1910.1053

Paragraph (a) applies the section to all occupational exposure to respirable crystalline silica except three groups. Construction work is excluded and sent to 29 CFR 1926.1153. Agricultural operations covered by 29 CFR part 1928 are excluded. So are exposures from processing sorptive clays. The section also does not apply where the employer has objective data showing exposure will stay below 25 micrograms per cubic metre of air under any foreseeable conditions.

ItemValue in the standard
Permissible exposure limit50 micrograms per cubic metre, 8-hour time-weighted average
Action level25 micrograms per cubic metre, 8-hour time-weighted average
Written results to affected employeesWithin 15 working days after an exposure assessment
Medical surveillanceAt no cost, for employees exposed at or above the action level for 30 or more days a year

A regulated area must be set up wherever exposure is, or can reasonably be expected to be, above the permissible limit. Paragraph (f) calls for engineering and work practice controls and a written exposure control plan. Respirators that meet 29 CFR 1910.134 are required while controls are being installed, for tasks where controls are not feasible or not sufficient, and inside a regulated area.

Sources