Protecting the climbing line from your own saw: what the ICoP, NSW and NZ codes record
Only the ICoP names the saw striking the climber's connection to the anchor. The NSW and NZ codes cover two attachment points, a saw kept clear of climbing equipment, and rope withdrawn after damage.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work. Four documents are covered. They are the ICoP for Arboriculture: Tree Work at Height (Edition 2, May 2020) and the SafeWork NSW Tree works code of practice (March 2026). The others are the WorkSafe New Zealand Approved Code of Practice for Safety and Health in Arboriculture (November 2012) and the Australian unit AHCARB319 Use arborist climbing techniques.
Wording on saws and lines
None of the four documents has a sentence on protecting the climbing line from the climber's own saw as a topic. Three of them come close, in different words.
| Document | Section | Wording |
|---|---|---|
| ICoP | 3.9.1 | When tools are used in the tree, particularly cutting tools, all measures must be taken to eliminate, or at the very least minimise, the possibility of striking the systems used to connect the operator to the anchors |
| NZ code of practice | 3.1.6 | The saw is to be well clear of the operator and climbing equipment at all times |
| NSW code | 10.8 | When operating cutting equipment, workers should maintain two independent means of attachment to suitable anchor points, wherever practicable from independent anchor points |
| AHCARB319 | Unit | No wording on saws and ropes; the unit covers safety checks on ropes, harnesses, tools and equipment before climbing |
The ICoP
Section 3.9.1 of the ICoP sets a risk hierarchy for tools used at height. Tool choice rests on the hazards of the tool, the nature of the work, and the skill and experience of the operator. The code lists a pruning saw, a pole saw, a lightweight top-handled chainsaw and a larger rear-handled chainsaw as examples.
Under that hierarchy sits the sentence on cutting tools striking the systems that connect the operator to the anchors. The same section adds that further personal fall protection systems may be installed to improve stability or positioning.
Section 3.9.2 covers hauling. If the climbing or access lines are used to haul equipment, care should be taken that the method of attachment or direct contact with the tool does not damage the ropes.
For chainsaws at height, the ICoP asks for appropriate training and a relevant certificate of competence or national qualification, unless the operator is in training and adequately supervised.
The New Zealand code
Section 3.1.6 covers chainsaws aloft. The climber shall be attached by two anchor points when making cuts aloft, and the saw is to be well clear of the operator and climbing equipment at all times. The same section asks for the best cutting position to limit the risk of being struck by the saw, including kickback, or by severed wood.
Chainsaws shall be secured in trees unless there is danger of the saw being trapped and taken with the severed section. Section 3.1.2 calls a tear-away chainsaw lanyard or tool strop attachment recommended practice aloft.
The code defines a cambium saver as a device that protects the bark, the cambium and the climber's line from friction damage. Section 3.2.4 adds that climbing lines and equipment are stored to prevent damage from contact with sharp tools, petrol, oil, excessive sunlight or chemicals.
The New South Wales code
Section 10.8 lists controls for chainsaws in trees. They include two independent means of attachment when operating cutting equipment, wherever practicable from independent anchor points, and attaching the saw by a tool lanyard when working above ground. Section 4.9 repeats the two points of attachment, preferably from independent anchor points.
Section 4.3 asks whether the location prevents climbing and roping ropes from crossing or overlapping, because friction between them could cause rapid failure of the climbing rope.
Rope found damaged
The codes agree that damaged rope leaves service. NSW section 4.2 says rope made unsafe by damage, defect or wear should not be used and should be removed from service. NZ section 3.2.4 says climbers shall check lines for damage, cuts, abrasion or deterioration before each use and remove them from service if signs of excessive wear or damage are found.
ICoP section 3.11.8 says equipment found defective in use or on inspection must be withdrawn from service immediately. It may be quarantined for examination by a competent person. Equipment that cannot be repaired should be indelibly marked against inadvertent use or, if necessary, destroyed.
The ICoP and the two codes name no test for judging a cut in a rope. The guide to inspecting climbing ropes and lines sets out what the inspection documents say.
Sources
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, sections 3.7, 3.9 and 3.11, read October 19, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, sections 3.1.2, 3.1.6, 3.2.4 and glossary, read October 19, 2026
- SafeWork NSW, Tree works code of practice, March 2026, sections 4.2, 4.3, 4.9 and 10.8, read October 19, 2026
- Australian Government, Skills Insight, AHCARB319 Use arborist climbing techniques, Release 1, read October 19, 2026