ArbNation Join free

Pruners, loppers, pruning saws and hedge shears: the cut sizes three extension services print

Three university extension sheets describe hand pruners, loppers, pruning saws, pole tools and hedge shears, and each prints a branch diameter for each tool. The diameters differ from sheet to sheet, so they are set side by side.

Checked against the sources at the bottom of this page on October 9, 2026. Rules, fees and pay change: the source has the last word.

The three sheets are written for gardeners and fruit growers, not for tree crews, and none of them is a regulator or a standard. Cleaning and disinfecting of the same tools is on the disinfecting pruning tools guide.

Cut sizes side by side

"Not stated" means the sheet prints no diameter for that tool. The sheets disagree, and the table does not pick one.

ToolNC StateNebraskaMinnesota
Hand pruners or shearsSmall limbs, usually less than 1/2 inchUp to 3/4 inchUp to 3/4 to 1 inch
Loppers1/2 inch to about 1 1/2 inches3/4 to 1 1/2 inchesUp to 1.5 to 2 inches, and some can cut larger
Pruning saw or hand sawLarger than 1 1/2 inchesLarger than 1 3/4 inchesNot stated
Pole prunerNot statedUp to 2 inchesNot stated
Pole sawNot statedUp to 2 inchesNot stated
Hedge shearsFor formal shrubs; manual, gas, electric and battery modelsFor shearing formal hedges to a size and shape; "should not be used to prune trees and shrubs"Not covered

Anvil and bypass blades

All three sheets describe two blade styles, for hand pruners and for loppers. In an anvil tool one sharpened blade cuts down onto a flat anvil. In a bypass tool, which Nebraska calls scissor-type, a sharp blade slides past the other blade.

  • NC State says many people regard anvil shears as poor tools but that this is not necessarily true, because anvil designs with a curved anvil and blade make a much cleaner cut. Bypass shears, when sharp, make clean cuts and get into small branch angles easily, and they are by far the most commonly used hand pruners.
  • Nebraska says scissor-type pruners are usually preferred over anvil types. Anvil types cannot cut as close and are more likely to crush stems.
  • Minnesota says bypass blades are considered to give a cleaner cut, while anvil blades can pinch the branch as they pass through. Bypass blades are single beveled and anvil blades double beveled.

Loppers: handle and force options

NC State gives lopper lengths from about 20 to 40 inches, with handles of wood, metal or fiberglass. Gears or ratchets add weight, and pneumatic, hydraulic and electric shears or loppers exist for big jobs. Nebraska describes four lopper features. Telescoping handles extend the reach. Ratcheting loppers hold the blades in place between squeezes. Compound loppers use a pivot arm that amplifies the force applied. Geared loppers use a gear mechanism for the same purpose. Both geared and compound loppers usually remove a branch in one cut. Minnesota lists manual, ratcheting and electric loppers, some with extending handles.

Hand saws and pole tools

NC State describes curved and straight hand saws, folding saws and saws with a hooked end that keeps the blade in the cut. Most of the saws it describes cut only on the pull stroke. Tri-edge or turbo blades have three-beveled teeth that cut smoothly with little clogging. Other blades have small teeth at the pointed end and larger teeth at the back, so that the cut starts with the finer teeth. If there is a question between loppers and a saw, the saw is often the better choice because it can get into tighter places with less crushing of tissue.

Minnesota describes the hand saw most used for dormant pruning as one with a slightly curved blade, large jagged teeth and usually a folding mechanism. Pole saws can be manual or electric, and an electric pole saw looks like a small chainsaw. Nebraska describes a pole pruner as a stationary hook and a hinged blade worked by a rope on a long wooden or fiberglass pole. NC State says aluminum pole sections are rigid and fiberglass lighter but very flexible. Dielectric fiberglass poles made for tree clearance work do not conduct electricity, and people need specific training and certification to work around electrical utilities.

Chain saws in the sheets

NC State says most arborists and tree climbers use chain saws to remove and prune larger trees and limbs, and that a chain saw should be used only after proper training. Nebraska says chain saws are often used by professional arborists on large branches, and that home gardeners are advised to use pruning saws instead. The guide to chainsaw regulator pages by country covers saw rules from the regulators.

Blade care

Minnesota describes carbon steel, stainless steel and coated steel blades. Carbon steel performs well but is susceptible to corrosion from moisture and plant sap. Stainless steel resists rust but is softer and may need sharpening more often, and coatings can wear off. Sharpening follows the natural bevel angle, given as 10 to 20 degrees, and a light coating of oil on the blade and on bolts, cogs and springs helps prevent rust after cleaning. NC State says a saw is protected by a scabbard or sheath, and that cutting a stem too big for a pair of pruners damages both the plant tissue and the tool.

Sources