Cleaning, upkeep and storing a saw: what makers and regulators list
Three safety bodies and one saw maker publish lists for saw upkeep, cleaning and storage. Three of the six sources are pages from that maker's UK site. A table at the end shows where the lists differ.
Checked against the sources at the bottom of this page on October 9, 2026. Rules, fees and pay change: the source has the last word.
Nothing here teaches maintenance or counts as repair advice. Regulators' pre-use checks are compared in the guide to chainsaw pre-use checks by regulator. The manuals that hold the real intervals for each saw are linked in the guide to saw and machine manuals.
The regulators' lists
The Canadian Centre for Occupational Health and Safety (CCOHS) fact sheet on chainsaw maintenance and service was last revised April 24, 2024. It is organised under six headings: general points, the engine, the chain and guide bar, adjusting chain tension, chain brakes and chain lubrication. Its general points: routine maintenance and service can minimize the hazards, and the maker's instructions in the operator's manual are the reference. Saws are returned to a service centre periodically, given as every few months to a year depending on usage. Storage procedures are followed if the saw will not be used for some time, and it may be necessary to drain the fuel and oil mixture. Under the engine it lists keeping the muffler and air intake filter clean with the spark arrester in place. CCOHS cites the CSA standard Z62.1-15 (R2020), which recommends that average brake stopping time not exceed 0.12 seconds and maximum stopping time not exceed 0.15 seconds.
The Western Australian regulator WorkSafe WA, on a chainsaws page updated April 1, 2025, has two maintenance lists. The first is a field maintenance list of things to have nearby during extensive cutting. It names ready-mixed two-stroke fuel, bar oil, and tools for tightening the chain or removing the sprocket casing. Also listed are cloth for spilt fuel or oil, a file and file guide for sharpening after every refuel, a portable vice for the bar during sharpening, and a small brush for the air filter and around the chain sprocket. The list also covers storing fuel and tools at least 10 metres from where cutting is done. The second is a list for after use. It has reversing the bar top to bottom to avoid wear on one side, cleaning the bar groove, cleaning the saw particularly at the air filter, cooling inlets and inside the sprocket cover, and cleaning the chain brake mechanism. Regular servicing in line with the maker's instructions is listed too.
The Health and Safety Executive (HSE) leaflet AFAG308, Top-handled chainsaws, covers petrol top-handled saws for off-ground arboricultural work. Its maintenance section says maintenance follows the maker's handbook, then gives a sample checklist. It starts with equal cutter lengths, specified cutter angles and depth gauge profiles. Then come inspecting the chain at each sharpening for abnormal wear; checking the guide bar rails for cracks and distortion; and checking the drive sprocket periodically. The list also has making no adjustments other than to the carburettor with the engine running; inspecting the anti-vibration rubbers frequently; and using only recommended non-flammable cleaner, with no petrol used to clean any part. Defects are reported without delay.
The maker's lists
The maker's UK site has three pages on the subject. Its maintenance page, dated December 8, 2025, recommends maintenance or cleaning before and after every use and refers to the operating instructions for intervals. Its list for each use includes a visual check for damage, the throttle trigger and its lockout, the chain brake, the condition of chain and bar, chain lubrication, tank caps sealed and no fuel leaking. For petrol saws it adds regular cleaning of the air filter and its housing, and checking the spark plug for wear and removing soot. For cordless saws it adds clearing the battery slot and cleaning its contacts. Cleaning after every use is called the most important measure, because resin and sawdust with chain lubricant can accumulate and harden.
The cleaning page, dated July 14, 2026, lists the air intake slits, the sprocket cover area, the guide bar groove and oil ports. For a longer break of three months or more it describes a more thorough clean. That list includes removing the bar and chain and storing them separately sprayed with care oil, cleaning the housing, and filling the chain oil tank completely for a biodegradable chain oil. For cordless saws it gives a battery storage charge level of two illuminated LEDs, with the battery stored apart from the saw and the charger. For petrol saws it describes emptying the fuel tank in a well-ventilated place and running the engine until it stops so the carburettor diaphragms do not stick.
The storage page, dated July 13, 2023, lists draining the tank, idling the engine until it stops, and removing and oiling the bar and chain. It also lists cleaning the cylinder ribs and air filter, and keeping the saw in a dry, well-ventilated place out of direct sunlight. Semi-synthetic chain oil does not gum and can stay in the tank. The saw is kept out of reach of children, ideally in a lockable room or cupboard. It can be stored vertically or hanging only when the fuel tank is empty.
Where the lists differ
| Item | Regulators | The maker |
|---|---|---|
| Bar turned over | WorkSafe WA: after each job | Turned over and deburred at regular intervals or on signs of wear |
| Chain brake | CCOHS: housing removed and cleaned periodically; WorkSafe WA: cleaned after use | Tested before each use |
| Air filter | CCOHS and WorkSafe WA: kept clean | Cleaned regularly with its housing |
| Service by a dealer | CCOHS: every few months to a year; WorkSafe WA: regularly per the maker | Intervals are in the operating instructions |
| Fuel in storage | CCOHS: may need draining | Drained, with the engine idled until it stops |
None of the sources gives a number of hours or months between air filter cleans or plug checks. The maker's pages and the regulators send the reader to the saw's own manual for that.
Sources
- Chainsaw maker's UK site, expert advice on chainsaw maintenance, December 8, 2025, read October 9, 2026
- Chainsaw maker's UK site, expert advice on how to clean a chainsaw, July 14, 2026, read October 9, 2026
- Chainsaw maker's UK site, chainsaw storage and care tips, July 13, 2023, read October 9, 2026
- Canadian Centre for Occupational Health and Safety, Chainsaws: Maintenance and Service, revised April 24, 2024, read October 9, 2026
- WorkSafe Western Australia, chainsaws, updated April 1, 2025, read October 9, 2026
- Health and Safety Executive, AFAG308 Top-handled chainsaws, read October 9, 2026