ArbNation Join free

Sawmill types compared: band, circular, frame and chainsaw machines in HSE, OSHA and WorkSafeBC texts

HSE's HSG172 describes band, frame, circular and chainsaw machines one by one. OSHA 1910.265 and WorkSafeBC Part 27 set guarding rules by saw type. None of the three defines a swing-blade mill.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The facts on this page come from HSE, OSHA and WorkSafeBC. It is not training and does not teach the work.

HSE's HSG172, Health and safety in sawmilling (second edition, 2012), is guidance, and HSE says following it is not compulsory. OSHA 1910.265 is the US federal sawmill standard. WorkSafeBC Part 27 is the British Columbia regulation for wood products manufacturing, which applies to workplaces that process logs or other wood into lumber, shakes, shingles, chips, plywood and particleboard.

Machine types in the three texts

Sawmill machine types and how each text describes them
TypeDescriptionWhere
Reciprocating carriage log band saw (vertical band mill)The log is held on a carriage that runs on rails to one side of the saw unit. The carriage is driven by steel cables or hydraulics. Head blocks support the log and gripping dogs hold itHSG172 paragraphs 81 to 83
Travelling table band sawLogs sit on a table fed to the blade by hand or under power. A log gripping device such as removable log hooks is normally required to keep them in line for cuttingHSG172 paragraph 78
Moving head-rig log band sawThe saw unit moves on rails through stationary timber, cutting horizontally or vertically. A less common layout feeds the log by slow track through a fixed horizontal head-rig, called a through and through machineHSG172 paragraphs 86 and 87
Band head sawOSHA defines a head rig as a head saw plus log carriage for the initial breakdown of logs into timbers, cants and boards, and sets rules for band head sawsOSHA 1910.265(b)(17), (e)(2)
Band resawHSG172 puts single-cut band re-saws in secondary breakdown, cutting slabs from partly sawn logs or boards from squared timber. OSHA defines a resaw as a band, circular or sash gang saw that breaks slabs, cants or flitches into lumberHSG172 paragraph 90; OSHA 1910.265(b)(32)
Frame sawA fixed rectangular frame holding a number of reciprocating blades for single or multiple ripping, fed by a powered carriage. HSG172 lists it as a primary breakdown saw for round timberHSG172 paragraph 98
Whole-log sash gang saw (Swedish gang)Named in OSHA's rules for head saws, with guarding for cranks, pitman rods and moving parts, enclosed feed rolls and carriage cradles high enough to stop logs kicking outOSHA 1910.265(e)(2)(v)
Circular log sawA primary breakdown saw with one or more circular blades. HSG172 also covers the travelling table circular log saw, or circular rack saw, which can be stationary or transportable on wheelsHSG172 paragraphs 101 and 106
Double slabber (dual circular rip saw)Two circular blades on one horizontal shaft or on separate shafts, adjustable towards or apart from each other. They cut small diameter logs and are often used in fence post manufactureHSG172 paragraph 111
Circular head saw and twin circular rigOSHA's single circular head saws, double circular mills with an upper saw, and twin rigs such as scrag saws. A husk is the head saw framework on a circular millOSHA 1910.265(b)(19), (e)(2)(iii) and (iv)
Multi-rip saw or straight-line edgerMachines that break down timber along its length, fed by hand or automaticallyHSG172 paragraph 122
Static cross-cut chainsawA fixed machine that trims logs or cross-cuts timber packs on a purpose-designed platform. Its guide bar runs from about the length found on a portable chainsaw to 2 m or moreHSG172 paragraph 147
Portable hand-held chainsawMost sawmills have one, used for example to trim individual logs before processingHSG172 paragraph 150
Drag sawOSHA defines it as a power-driven, reciprocating crosscut saw on a frame, used for bucking logsOSHA 1910.265(b)(15)
Swing-blade millNo definition in the three texts. They name swing saws only as OSHA's swing saws on log decks and the swing cutoff saw in WorkSafeBC section 27.23None

Band saws

HSG172 says band saws for primary and secondary cutting come in vertical or horizontal form. They are either stand-alone with manual feed or in-line with mechanical or automated feed. It points to BS EN 1807:1999 for the band saw standard. As a general principle it puts normal operating controls on log band saws at least 1.2 m from the cutting area.

For manually controlled log band saws with a single cutting edge, HSG172 describes a guard enclosing the blade on at least the cutting edge and outer side. A blade with two cutting edges needs a guard on at least three sides.

WorkSafeBC section 27.19 requires a band saw and its wheels to be enclosed or guarded except in the cutting area. The aim is to prevent worker contact and restrain the blade if it fails. Section 27.30 sets crack limits in Table 27-2. A band saw wider than 300 mm, for example, comes out of service for a crack over 19 mm. Section 27.31 requires a band saw wheel over 1.2 m in diameter to be tested for cracks at least once a year.

OSHA 1910.265 requires wheels to be completely encased or guarded, except the part of the upper wheel where the blade leaves it. Band head saw wheels get monthly inspections. A band saw with a crack greater than one-tenth of its width cannot be placed in service until it is repaired or the crack is stopped.

Circular saws

HSG172 points single blade log saws to BS EN 1870-7:2002. For the cutting area it describes a deterring device of wire mesh with gaps no larger than 30 mm by 60 mm, at least 1.4 m high and at least 1.1 m from the blade. The braking time should be under ten seconds. Where run-up takes longer than ten seconds, braking should take less than the run-up and no more than 30 seconds. All circular saws used for ripping need a properly adjusted riving knife, which stops cut timber binding on the blade and causing kickback.

WorkSafeBC treats circular saws separately. Section 27.18 requires blade portions outside the cutting area to be fully guarded. Section 27.22 requires a splitter on a saw with rip-type teeth where kickback could reach a worker. Section 27.24 requires safety guides on circular head saws and scragg saws.

OSHA 1910.265 sets safety guides that adjust without hand tools, a hood on the upper saw of a double circular mill, and a spreader wheel or splitter where live rolls are not used behind the head saw. Circular gang resaws need a hood over the bank, anti-kickback devices and spreaders.

Frame saws, chainsaw machines and the gaps

HSG172 lists the hazards of a frame saw as contact with the reciprocating blades, being drawn in at the feed rollers, entanglement at the carriage drive and very high noise. For static cross-cut chainsaws with automatic or remote cross-cutting, it describes guards that stop access to the cutting area from the operating position and from beside the feed table.

On the hand-held chainsaw, HSG172 says anyone operating one at the mill needs training for the jobs they do. It adds that nobody should help the operator by holding the timber being sawn.

None of the three texts describes a swing-blade mill or a chainsaw milling attachment, and none sets capacities for any mill type. The guide to sawmilling and chainsaw milling covers the California rule on ripping logs.

Sources