ArbNation Join free

Sit harness, positioning belt and full-body harness: which standard each use points to

The UK industry code, the Canadian New Brunswick regulation and the New South Wales tree code name different standards for sit harnesses, work positioning belts and full-body harnesses. The table lines them up by use.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The three documents are the UK Industry Code of Practice for Arboriculture, Tree Work at Height (Edition 2, May 2020), a WorkSafeNB interpretation of General Regulation 91-191, and the SafeWork NSW Tree works code of practice. That code commenced on March 27, 2026. Harness types are described in the guide to saddles and harnesses by type.

The table by use

UseStandards named, by document
Work positioning with a sit harness or saddleUK industry code: BS EN 813, Sit harnesses, and BS EN 358, Belts and lanyards for work positioning or restraint.
New Brunswick: CSA Z259.1-05, Body Belts and Saddles for Work Positioning and Travel Restraint.
New South Wales: AS/NZS 1891.1:2020 and AS/NZS 1891.4:2025.
Fall arrest with a full-body harnessUK industry code: BS EN 361, Full body harnesses.
New Brunswick: CSA Z259.10-18, Full body harnesses.
New South Wales: AS/NZS 1891.1:2020 and AS/NZS 1891.4:2025, listed against the safety harness in the PPE table.
Rope accessUK industry code: BS EN 12841, Rope access systems, rope adjustment devices.
New Brunswick: no rope access entry in the list.
New South Wales: AS/NZS ISO 22846.1:2020, Rope access systems, fundamental principles for a system of work.
Mountaineering and climbing harnessUK industry code: BS EN 12277, Mountaineering equipment, harnesses.
New Brunswick: no entry in the list.
New South Wales: no entry in the code.

United Kingdom

The industry code lists its work equipment standards in Part 6. The list covers BS EN 361, BS EN 358, BS EN 813 and BS EN 12277 among its 27 entries. It carries no note on which harness suits which task. The code defines a harness as an assembly of elements worn by a user to provide points for connection to systems, adjustable to fit and able to support an operator in suspension, by a ventral, sternal or dorsal attachment.

BSI records BS EN 813:2008 as published on September 30, 2008 and withdrawn on March 27, 2024. Its scope is sit harnesses for restraint, work positioning and rope access systems where a low point of attachment is required. The scope adds that sit harnesses are not suitable for fall arrest. BSI records BS EN 361:2002 as current and under review.

Canada

WorkSafeNB reads section 49.1 of General Regulation 91-191, issued October 8, 1997 and revised March 1, 2023. The regulation makes owners, employers and contractors each responsible for fall-protection components that meet the applicable standards. Subsection 49.1(2) names the CSA standards. They include Z259.1-05 for body belts and saddles and Z259.10-18 for full body harnesses. The list also names Z259.11-17 for energy absorbers and lanyards and Z259.12-16 for connecting components. Most entries are followed by the words "or a standard offering equivalent or better protection", and WorkSafeNB notes that this reading applies to all similar wording in references to standards.

Australia and New Zealand

SafeWork NSW section 4.4 describes a work positioning harness as an adjustable waist belt joined to a pair of leg loops or a sit strap, built to support the climber in a sitting position while suspended. The code limits it to situations that may result in a restrained fall or a limited free fall, and says it should not be used where a free fall greater than 600 mm is possible. The harness should stop the wearer slipping out if inverted. If it cannot do that, a full-body harness should be worn instead. For further guidance it points to AS/NZS 1891.1:2020 and AS/NZS 1891.4:2025.

The code's glossary defines a work positioning harness as an assembly of a body belt and buttock strap for use as a work positioning device, where only a restrained fall is likely. The crane access section says harnesses used for rope access methods in tree climbing are not suitable for the crane access method. Table 7 lists AS/NZS 1891.1:2020 and AS/NZS 1891.4:2025 against the safety harness, which protects against falls from height.

Where the lists differ

The UK list names a separate standard for the positioning belt (BS EN 358) and one for the sit harness (BS EN 813). The Canadian list folds belts and saddles into one standard, Z259.1-05. The New South Wales code points to one pair of AS/NZS standards for both kinds of harness.

Sources