ArbNation Join free

Soil pH and liming or acidifying around trees: what extension says

Extension sources name different best pH ranges for trees, from 5.5 up to 7.5. High pH locks up iron and manganese and shows as chlorosis, and lime or sulfur change the soil slowly.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

This page draws on four extension and agency publications about soil pH and trees. It is not training and does not teach the work. Colorado State University (CSU) PlantTalk covers iron chlorosis in trees. The Wisconsin Department of Natural Resources (DNR) covers chlorosis causes. Iowa State lists trees for alkaline soil. Clemson's HGIC 1650 covers changing soil pH in South Carolina gardens.

The pH ranges given

Soil pH ranges named in the sources
SourceRange and meaning
Wisconsin DNRpH 5.5 to 6.5 is optimal for nutrient uptake in most trees. Some conifers prefer 5.0 to 6.0
Iowa StateTrees and shrubs grow best in slightly acidic to slightly alkaline soil, pH 6 to 7.5. Iowa soils run from 5.5 to 7.5, many near the high end. Alkaline means above 7.0
CSU PlantTalkAbove pH 7.5, the best control for iron chlorosis is to avoid trees sensitive to it. Colorado soils are mostly alkaline
Clemson HGIC 1650Most ornamentals do best at 5.8 to 6.5. Acid-loving plants, a list that includes conifers, azaleas, rhododendrons and blueberries, do best at 5.0 to 5.5. Neutral is 7

The ranges differ, so the sources do not give one target for every tree. Clemson adds that values outside its ranges can mean reduced vigour and nutrient deficiencies, and that above pH 6.5 phosphorus and most micronutrients become less available. In highly acidic soils, aluminum and manganese can become more available and more toxic, and calcium, phosphorus and magnesium less so.

Acid and alkaline tolerance

Iowa State publishes lists for soils where a test shows alkaline conditions. Shade trees on the tolerant list include boxelder, bitternut hickory, northern catalpa, common hackberry, honeylocust, coffeetree, bur oak, American basswood and littleleaf linden. Small trees include eastern redbud, hawthorn and Peking lilac.

Its intolerant list names red maple, river birch, bicolor oak and pin oak, plus azaleas, rhododendrons and blueberries. Iowa State says gardeners seldom see pH problems in the state unless a species is particularly sensitive to higher pH, such as pin oak.

CSU names maples (red, silver, Amur), oaks (red, swamp white), aspen, apple and crabapple, peach and some pines as often developing iron chlorosis in Colorado.

Iron chlorosis and the pH link

Wisconsin DNR describes chlorosis as yellow leaves with green veins, often from a shortage of iron and manganese. The minerals are usually in the soil but become unavailable to roots when pH is too high. Excess potassium, magnesium and phosphorus may also contribute. The damage is often temporary, but in severe cases branches or whole trees die, and more often another health problem is the cause, sometimes together with chlorosis. Wisconsin DNR lists oak wilt, bur oak blight, frost damage, two-lined chestnut borer and armillaria among them.

CSU gives the same picture for Colorado. Soils there hold adequate or high iron, but alkaline conditions leave most of it in an insoluble form. The newest leaves at branch ends yellow first, the veins stay green, and in advanced cases the edges scorch. Low soil oxygen, from compacted clay or overwatering, can make it worse or bring it on in less prone trees, and so can too much phosphorus.

Treatments for chlorosis

  • Wisconsin DNR starts with soil and foliage nutrient tests through the University of Wisconsin Soil and Forage Lab. Chelated iron and sulfur are the soil amendments it names as commonly used, and it expects time and cost to limit treatment to yard trees and trees at forest edges.
  • CSU lists iron sulfate, whose effectiveness may be limited, iron chelates, some more effective than others depending on alkalinity, and sulfur to lower pH, less feasible where soil is high in lime. Foliar iron sprays are often impractical on large trees and last only a short time. Trunk injections can open entry for disease organisms and are best left to certified arborists. CSU adds that above pH 7.5 the best control is avoiding sensitive trees.
  • Clemson says to test the soil before adjusting pH.

Liming and acidifying

Clemson lists ground agricultural limestone as the most frequent way to raise pH. Finer particles react faster, and clay and organic soils need more than sandy soil for the same change. Limestone is applied in fall or winter, ideally two to three months before planting, and it reacts slowly in dry soil. Hydrated lime acts faster than regular limestone and is flagged for caution. Clemson also describes wood ash as a gradual way to raise pH and says coal ash has no lime value.

To lower pH Clemson names elemental sulfur and aluminum sulfate. Sulfur works gradually, as soil bacteria turn it into sulfuric acid, and the speed depends on moisture and temperature. It can take several months. Aluminum sulfate acts immediately once dissolved, with a greater risk of root injury and aluminum build-up from overuse. Clemson gives rate tables for loamy soil in pounds per 10 square feet, less for sand and more for clay. Clemson writes for South Carolina gardens, not for the root zone of a tree.

Oxygen and compaction are the subject of the guide to soil decompaction, and the plant health care primer sets chlorosis in the wider approach to tree problems.

Sources