Standards register addendum: ASTM F887 climbing equipment, ANSI B175.1 chain saws, the NESC and the SAE standards in OSHA 1910.266
ASTM F887-23 covers personal climbing equipment, the NESC covers overhead and underground utility lines, and OSHA 1910.266 ties chain saws to ANSI B175.1-1991. This register gives each standard's edition and scope.
Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here.
ASTM F887-23, personal climbing equipment
ASTM lists F887-23, Standard Specifications for Personal Climbing Equipment, as an active standard, last updated December 11, 2023. It belongs to Committee F18 and to volume 10.03 of the ASTM book of standards. The store page lists earlier versions back to F887-97, among them F887-20, F887-18, F887-16, F887-13, F887-12 and F887-05.
Section 1.1 of the scope covers the specifications and qualification testing of these items:
- climbers, climber straps, climber pads and climber footplates
- body belts and work positioning devices with locking snaphooks or carabiners
- wood pole fall restriction devices
- the arborist saddle, harnesses and energy absorbing lanyards
ASTM states that these devices are used by workers climbing poles, trees, towers and other structures. The standard also sets minimum performance criteria for harnesses and energy absorbing lanyards that arrest a fall after exposure to electric arcs, for workers who may meet the thermal hazards of momentary electric arcs or flame.
Section 1.2 sorts equipment into five categories.
| Category | ASTM definition |
|---|---|
| Fall (travel) restraint | Prevents a user from reaching a fall hazard, with 0 fall distance allowed. |
| Work positioning | Allows a 2 ft maximum free fall distance. |
| Fall arrest | Allows a 6 ft maximum free fall distance with a maximum arrest force of 1800 lb. A note allows a 12 ft free fall with the same force, under certain conditions and with equipment designed for them. |
| Suspension | Allows 0 free-fall distance while supporting the user's weight. |
| Fall restriction | Prevents or limits free fall from a work position or while ascending or descending a wood pole. |
The scope counts three types of climbers (A, B and C) and two types of climber straps. It counts two types of body belts and eight types of work positioning devices. It adds two types of wood pole fall restriction device, one arborist saddle (Type A), two types of harness and two types of energy absorbing lanyard. ASTM gives the values in US customary units as the standard, with SI conversions for information only.
IEEE C2-2023, the National Electrical Safety Code
IEEE SA lists the 2023 National Electrical Safety Code (NESC) as IEEE C2-2023, an active standard published 2022-08-01 that supersedes C2-2017. Its scope covers practical safeguarding of people during the installation, operation or maintenance of electric supply stations, overhead supply and communications lines, and underground or buried supply and communication cables. It also includes work rules for the operation of electric supply and communications lines and equipment.
The Code consists of the introduction, definitions, grounding rules, lists of referenced and bibliographic documents, and Parts 1, 2, 3 and 4 of the 2023 edition.
Standards that OSHA incorporates by reference
OSHA 1910.6 lists the consensus standards that the agency has incorporated by reference into its rules. Section 1910.266 is the logging operations standard, and it cites the following ones.
| Standard as OSHA cites it | Where 1910.266 uses it |
|---|---|
| ANSI B175.1-1991, Safety Requirements for Gasoline-Powered Chain Saws (1910.6(e)(32)) | Paragraph (e)(2)(i). A chain saw placed into initial service after the effective date must have a chain brake and otherwise meet B175.1-1991. A saw placed into service earlier must have a device that minimizes kickback, and no kickback device may be removed or disabled. |
| SAE J386, June 1985, Operator Restraint Systems for Off-Road Work Machines | Machine seat belts, paragraph (d)(3)(iv). |
| SAE J1040, April 1988, Performance Criteria for Rollover Protective Structures (ROPS) | Machines manufactured after August 1, 1996, paragraph (f)(3)(ii)(B). |
| SAE J231, January 1981, Minimum Performance Criteria for Falling Object Protective Structures (FOPS) | FOPS, paragraph (f)(3)(iii). |
| SAE J397, April 1988, Deflection Limiting Volume, ROPS/FOPS Laboratory Evaluation | Paragraph (f)(3)(iv). |
| SAE J185, June 1988, Recommended Practice for Access Systems for Off-Road Machines | Machine access, paragraph (f)(5)(i). |
Section 1910.6 also incorporates ANSI Z89.1 head protection (the 1997, 2003 and 2009 editions among others), ANSI Z87.1 eye protection (1989, 2003 and 2010 among others) and ANSI Z41 protective footwear (1991 and 1999 among others). ASTM F2412-2005 and F2413-2005 cover foot protection. The OSHA personal protective equipment rules in 1910.133, 1910.135 and 1910.136 are where those editions apply.
OSHA's wider rules for tree work are covered in the guide to OSHA standards for tree work. The main US and British standards are covered in the standards register.
Sources
- ASTM International, F887-23 Standard Specifications for Personal Climbing Equipment (store page), read October 15, 2026
- IEEE Standards Association, IEEE C2-2023, 2023 National Electrical Safety Code (NESC), read October 15, 2026
- US Department of Labor, OSHA, 29 CFR 1910.6 Incorporation by reference, read October 15, 2026
- US Department of Labor, OSHA, 29 CFR 1910.266 Logging operations, read October 15, 2026