Swivels, rigging plates and rings used in tree-climbing kits: ratings and standards
No standard or code in the record rates a swivel, rigging plate or ring by name. The nearest coverage is the connector and pulley standards: EN 12275, EN 362, UIAA 121 and EN 12278.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The Industry Code of Practice for Arboriculture: Tree Work at Height (ICoP, Edition 2, May 2020) defines a connector as a component used to connect elements of a personal fall protection or rigging system.
Connector and pulley standards
| Standard | Catalogue entry |
|---|---|
| EN 12275, Mountaineering equipment. Connectors | Safety requirements and test methods for connectors used in mountaineering, climbing and related activities. They are part of the safety system that protects the climber from a fall from height. BSI lists BS EN 12275:2013 as current, published April 30, 2013. The Estonian standards body lists it as valid from May 6, 2013, under Regulation (EU) 2016/425 on personal protective equipment. |
| EN 362, Personal protective equipment against falls from a height. Connectors | Requirements, test methods, marking and manufacturer information for connectors used as connecting elements in fall arrest, work positioning, rope access, restraint and rescue systems. The Swedish standards institute lists SS-EN 362:2004, approved December 17, 2004, as valid. |
| UIAA 121 Connectors and UIAA 127 Pulleys | Both sit in the UIAA safety standards list, which spans more than 25 types of equipment. The list gives the numbers and a download link for each standard. |
| EN 12278, Mountaineering equipment. Pulleys | Named in Part 6 of the ICoP, the list of work equipment standards. The ICoP list gives the title only. |
The UIAA began creating safety standards in 1960 and works with CEN, the European Committee for Standardization. In some cases it asks for extra tests, so a UIAA standard may differ slightly from the CEN one.
Figures printed for connectors
OSHA's personal fall protection standard, 29 CFR 1910.140, sets the American figures. It defines a D-ring as a connector used in a harness as an attachment element, in a lanyard, energy absorber, lifeline or anchorage connector, or in a positioning or travel restraint system. The ICoP sets the British figure for connectors.
| Source and clause | Item | Figure printed |
|---|---|---|
| OSHA 1910.140(c)(7) | D-rings, snaphooks and carabiners | Minimum tensile load of 5,000 pounds (22.2 kN). |
| OSHA 1910.140(c)(8) | D-rings, snaphooks and carabiners | Proof tested to 3,600 pounds (16 kN) without cracking, breaking or permanent deformation. The gate must hold 3,600 pounds (16 kN) without separating from the nose by more than 0.125 inches (3.175 mm). |
| OSHA 1910.140(c)(9) | Snaphooks and carabiners | Automatic locking type, needing at least two separate, consecutive movements to open. |
| ICoP 3.10.6.5 | Connectors | Minimum breaking strength (MBS) of at least 22 kN, loaded on the major axis where applicable, with a locking mechanism. |
| ICoP 3.10.6.12 | Pulleys, blocks and trolleys | No kN figure. Rope diameter must suit the sheave diameter and cheek plate profile, and the cheek plates must prevent inadvertent opening in use. |
Compatibility and marking
OSHA 1910.140(c)(10) bars snaphooks and carabiners from being connected to each other, or to a D-ring that already carries another connector, unless they are designed for such connections. Under (c)(19), ropes, belts, lanyards and harnesses must be compatible with the connectors used.
The ICoP's general specification for fall protection components applies to each item. Each item is rated for the mass of the operator, including equipment worn, and carries enough information to trace it to the manufacturer, product name, construction properties and examination records.
Gaps in the sources
None of the sources names a swivel, a rigging plate or a ring. OSHA's definitions list carabiner, connector, D-ring and snaphook. The ICoP list has no standard for swivels or plates. An item's own rating, standard and marking come from its maker's instructions.
Sources
- OSHA, 29 CFR 1910.140 Personal fall protection systems, read October 21, 2026
- BSI Knowledge, BS EN 12275:2013 Mountaineering equipment. Connectors, read October 21, 2026
- Eesti Standardimis- ja Akrediteerimiskeskus, EVS-EN 12275:2013 catalogue entry, read October 21, 2026
- Swedish Institute for Standards, SS-EN 362:2004 Connectors, read October 21, 2026
- UIAA, Safety Standards list, read October 21, 2026
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, read October 21, 2026