Tailgate talk sheets: seven one-page hazard sheets from OSHA and HSE
One sheet each for traffic, drop zones, chippers, aerial lifts, power lines, lone working and machine maintenance. Each gives the hazard, what OSHA or HSE lists, a case where one exists, and five questions for the crew.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named publications are described here as published. It is not training and does not teach the work. The questions carry no answers.
Heat, cold, lightning, fatigue and first aid have no sheet. The OSHA publication and the HSE case page do not cover them, and the NIOSH FACE program page does not describe its reports in enough detail to build one. The case lines come from the HSE tree work case studies, where a case fits the hazard.
Sheet 1: Traffic control
The hazard
OSHA 3940, Solutions for Tree Care Hazards, says workers can be struck by moving vehicles and that the traffic zone could interfere with pedestrian traffic.
The OSHA 3940 list
- Briefing workers on traffic zone safety and site setup.
- Traffic control plans that include the proper use of control devices.
- Cones, barricades and flaggers to guide vehicles and pedestrians, with certified flaggers if the operation interferes with traffic.
- High visibility vests, a safe pedestrian route, and lights at night.
Case
The sources opened for this sheet hold no traffic case.
Questions
- Where will vehicles and pedestrians pass today?
- Who is the flagger, and what training does that person hold?
- What marks the edge of the work zone?
- Where does a pedestrian walk if the footpath is closed?
- What changes after dark?
Sheet 2: Drop zones
The hazard
OSHA 3940 says workers can be struck by falling trees, limbs and hand tools, with enough force for serious or fatal injury.
The OSHA 3940 list
- Cones or caution barrier tape to establish, mark and manage the drop zone.
- Training on drop zone entry and exit, and only qualified workers near the zone.
- A hard hat and eye protection.
- Visual or audible communication between overhead and ground workers, with a command and response such as "stand clear" and "all clear" before cutting and dropping limbs.
Case
The HSE case studies describe a 26-year-old man pulled out of a tree when his climbing strop broke. The climbing rope seems to have become entangled and taken the weight of a falling tree section, which fell awkwardly and dragged him from the tree.
Questions
- How is the drop zone marked on this job?
- Who may enter it, and by which route?
- What call does the climber give, and what answer comes back?
- Where does each climbing rope run in relation to the piece being cut?
- What happens if the answer from below does not come?
Sheet 3: Chippers
The hazard
OSHA 3940 says chipper hazards arise when workers push material by hand or lean too far into the hopper, that material can be thrown from the machine, and that chippers produce hazardous noise.
The OSHA 3940 list
- Training to inspect and operate chippers, and the maker's instructions.
- Standing to the side when feeding material.
- Safety glasses, a hard hat and hearing protection; close-fitting clothing, gloves without cuffs and skid-resistant shoes.
- Ropes and lines stowed away from the chipper, cut end fed first, only wood fed in, and no reaching into the in-feed chute to clear a jam while the machine runs.
Case
The sources opened for this sheet hold no chipper case.
Questions
- Who is trained on this chipper?
- Where do the ropes and lines sit while it runs?
- How is a jam handled on this crew?
- Which clothing and gloves are in use today?
- What is the noise protection, and does everyone have it?
Sheet 4: Aerial lifts
The hazard
OSHA 3940 says workers can fall or be thrown from a raised bucket. It names falls, electrocutions, and equipment collapses or tip-overs as the major causes of injury and death.
The OSHA 3940 list
- Only qualified and trained workers operate aerial lifts.
- Guards, controls and emergency shut-off devices working, and the lift and worksite inspected before each use.
- Outriggers on pads or a level, solid surface, brakes set, and wheel chocks on slopes.
- A body harness or restraining belt with a lanyard attached to the bucket, tied to an approved anchor point, standing firmly on the floor, no overreaching, and no climbing spurs inside the bucket.
- The bucket not used for material handling unless designed for it.
Case
The sources opened for this sheet hold no aerial lift case.
Questions
- Who inspected the lift today, and where is the inspection written down?
- What is under the outriggers?
- Where is the lanyard attached?
- Which lines or obstructions are within reach of the boom?
- Who is on the ground, and what can they do from there?
Sheet 5: Power lines
The hazard
OSHA 3940 says workers can be electrocuted when a limb, branch or uninsulated aerial lift touches a live power line.
The OSHA 3940 list
- Training to identify and avoid power line hazards before work begins.
- All overhead power lines and communication cables treated as energized, with at least 10 feet (3 meters) kept away unless qualified.
- If a line falls near a worker or equipment, moving away with short, shuffling steps and feet close together.
- No trimming in dangerous weather, no corded electric tools in trees near energized lines, and no metal or other conductive ladders near overhead lines.
Case
The HSE case studies describe a 65-year-old self-employed director electrocuted when the boom of a lorry-mounted timber crane touched an overhead line and caught fire. The boom appears not to have been fully stowed for travel. He was electrocuted as he got out of the cab. HSE adds that a line can switch back on automatically after tripping.
Questions
- Where are the lines on this site, and who has the map?
- Which of them is the closest to today's work?
- Who has the number of the line owner?
- What ladder is on the truck, and what is it made of?
- What would the crew do if a line came down near the truck?
Sheet 6: Lone working
The hazard
The HSE case studies describe a 68-year-old self-employed forester working alone who is thought to have fallen and died of head injuries. Nobody saw it. A family member's concern led the works manager to find him.
The HSE list
- Keeping the work area as clear as practicable, especially with chainsaws.
- Suitable footwear, replaced when worn, and attention to where one walks on difficult terrain.
- Reliable procedures to know where lone workers are and what they are doing, and a way to keep in touch.
- An arrangement to confirm a lone worker has left at the end of the day, not an assumption.
Questions
- Is anyone on this job out of sight of the others?
- How does the office know where each person is?
- Who confirms each person has left at the end of the day?
- What is the footing like on the way to the work?
- Who can reach a person on the ground if they are hurt?
Sheet 7: Machine maintenance
The hazard
The HSE case studies describe a 59-year-old employee run over by a forestry forwarder. He stood on the tracks and leaned into the cab to start the engine after a repair on a steep slope. The machine moved forward and threw him under the wheels.
The HSE list
- Starting a machine only from the driving position.
- No work on or under a machine while it runs, or with the key in the ignition and controls engaged.
- The Safe Stop sequence for maintenance: handbrake on, controls neutral, engine off, key removed.
- Maintenance to the maker's handbook, and operators suitably trained.
Questions
- Who holds the key during a repair?
- Where is the handbook for this machine?
- What is the ground like where the machine is parked?
- Who is trained on it?
- Where does everyone stand when the engine starts?
The FACE program
The NIOSH Fatality Assessment and Control Evaluation program, started in 1982, investigates selected fatalities and shares findings. Its investigators do not enforce standards and do not assign fault or blame. NIOSH and state reports include recommendations to prevent similar deaths. The reports are hosted on CDC Stacks.