ArbNation Join free

Tie-in with a saw: the two-anchor wording for cutting aloft in NZ, UK and NSW

Two codes use the words two anchors or two independent attachments for saw work in a tree: New Zealand's approved code and the NSW code of practice. The UK industry code asks for a backup and for care around the lines.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

Everything below is what the named codes and training bodies publish. It is not training and does not teach the work.

Second attachment when cutting, by source

SourceSecond anchor or attachmentSaw and lines
WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture (November 2012), clause 3.1.6The climber is attached by two anchor points when making cuts aloft. A secure position at or above the level of the cut is adopted.The saw is kept well clear of the operator and the climbing equipment at all times. A tear-away saw lanyard or tool strop is recommended practice aloft (clause 3.1.2).
SafeWork NSW, Tree works code of practice (March 2026), chapter 10.8When operating cutting equipment, workers should maintain two independent means of attachment to suitable anchor points, wherever practicable from independent anchor points.The chainsaw should be attached, for example by a tool lanyard, when working above ground.
Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height (Edition 2, May 2020), 3.8.6 and 3.9.1A backup is expected behind the primary system. It should use an independent anchor where possible. Additional personal fall protection systems may be installed to improve stability and positioning.When cutting tools are used in the tree, all measures must be taken to eliminate or at least minimise the possibility of striking the systems that connect the operator to the anchors.
HSE, Aerial work, United KingdomThe page prints no figure for a second anchor.Chainsaws should never be used off the ground unless the operator has been adequately trained in safe working techniques.

New Zealand: two anchor points

The New Zealand approved code applies the rule to chainsaw cuts made aloft. Clause 3.1.6 says chainsaws are secured when used in trees unless the saw could be trapped and taken with the severed section. A climber takes a secure position at or above the level of the cut. The code also asks for the best cutting position to limit the risk of being struck by the saw, by kickback or by severed pieces. Clause 3.2.2 adds that fall restraint should be used whenever a climber is aloft.

The same code, at clause 3.1.4, says a climbing saw is operated with two hands at all times or as the manufacturer's instructions say. Top-handled saws are not used on the ground. Drop starting is prohibited, and the extended arm technique is the approved starting method aloft.

New South Wales: two independent means of attachment

The NSW code took effect on 27 March 2026 and replaced the 1998 Amenity Tree Industry Code of practice. Its chainsaw controls for trees list climbers starting or operating saws only from a safe and stable working position. They list two independent means of attachment while operating cutting equipment, from independent anchors wherever practicable, and the chain brake applied between cuts.

The code's wider tree climbing chapter lists a second attachment point as a control measure: a climbing lanyard or a second rope system. It names four cases: cutting work in a tree, a risk of an uncontrolled swing, a risk of failure of the main line or primary anchor, and an anchor that is not above the work area.

For the saw's own lanyard, the NSW code says it should be long enough to allow full reach and to hang the saw below the climber's feet when not in use. Connection hardware that forms part of the lanyard should carry a load rating, be auto-locking, and need three consecutive actions to open. The lanyard should incorporate a weak link that lets it separate from the harness under extreme loading.

United Kingdom: backup, not a count

The Arboricultural Association's industry code does not print the words second anchor for saw work. Its criteria say the operator should be connected to a backup that gives a fail-to-safe if the primary system fails, covering ascent, movement around the tree and descent. The backup limits the distance and consequences of a fall. It uses an anchor independent of the primary anchor or, if none is suitable, is installed over a shared anchor. The code allows the backup to be omitted only where it is not practical to maintain it for specific, short-duration tasks.

The code's tools section is where the saw appears. Equipment is chosen by the hazards of the tool, the nature of the work and the skill of the operator, and it names pruning saw, pole saw, top-handled chainsaw and larger rear-handled chainsaw. Operators who use a chainsaw at height should hold appropriate training and a relevant certificate of competence or national qualification, unless they are in training and supervised.

HSE's aerial work page sets a minimum of two people present during all aerial work, and one of the ground team must be available, competent and equipped to do an aerial rescue without delay.

Where the sources differ

New Zealand fixes the number at two anchor points and gives no exception. NSW says two independent means of attachment and ties independent anchors to what is practicable. The UK code and HSE do not name a number for saw work. Other countries' wording is in tie-in points and second attachment, and the wider saw rules are in saw use aloft by country.

Sources