ArbNation Join free

Top-handled chainsaws: HSE leaflet AFAG308 and the WorkSafe NZ arboriculture code

HSE leaflet AFAG308 restricts one-handed use of a top-handled saw to extended reach while the other hand keeps a stable position, and calls poor positioning no reason. WorkSafe NZ's arboriculture code says that too.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

Everything below is what the named codes and training bodies publish. It is not training and does not teach the work.

Where the two documents stand

QuestionHSE, AFAG308WorkSafe NZ, arboriculture code
On the groundTop-handled saws are only suitable off the ground; operators use rear-handled saws on the groundTop-handled saws shall not be used on the ground
GripGrip both handles wherever possibleClimbing saw operated with two hands at all times, or as the maker's instructions say
One-handed useRestricted to cases where one hand holds a stable position and the saw is at extended reachPoor positioning is not an acceptable reason for one-handed use
LanyardSuitably rated or tear-away lanyard permitted; not where the saw could be trapped or taken by a severed sectionTear-away lanyard or tool strop recommended aloft
WhoTrained, competent climber with chainsaw experience, or a supervised trainee competent on the groundAdequate training for all operators; no chainsaw above shoulder height

HSE leaflet AFAG308

The leaflet, Top-handled chainsaws, was issued as revision 2 in April 2013, first published in December 2008. HSE's publication page for it was updated on August 7, 2025. It covers the safe working practices for a petrol-powered top-handled chainsaw used for arboricultural off-ground work. Tree work needing a chainsaw is for a trained and competent climber with chainsaw experience, or a trainee under supervision who is competent using a chainsaw on the ground. HSE also says to use the leaflet with the maker's handbook as part of a risk assessment.

The leaflet states that top-handled saws are only suitable for use off the ground, and that operators use rear-handled saws on the ground. It points readers to three companion leaflets: AFAG401 Tree-climbing operations, AFAG402 Aerial tree rescue and AFAG403 on MEWPs in tree work.

It sets out the minimum at the start of a climb. Two people are present during all tree-climbing operations, and one of the team is on the ground, competent and equipped to perform an aerial rescue without delay.

One hand or two

AFAG308 gives its position on grip in a short run of statements.

  • Top-handled saws have two handles, and to keep proper control the operator grips both wherever possible.
  • Incorrect, one-handed use sharply raises the risk of injury if the saw kicks back, skates or bounces on contact with a branch, or drops through at the end of a cut.
  • One-handed use should be restricted to circumstances where one hand is required to maintain a stable working position and the saw is used at extended reach with the other hand, for example while cutting at the extremities of limbs.
  • Poor work positioning in the tree is not an acceptable reason for one-handed use.
  • The leaflet says never to hold and cut a section, and not to try to catch a falling section.

The WorkSafe New Zealand Approved Code of Practice for Safety and Health in Arboriculture, November 2012, clause 3.1.4, carries nearly the same sentences about poor positioning and the risks of incorrect one-handed use. Its text is that a climbing saw is operated using two hands at all times or as the maker's instructions say, and that the saw is stopped or the chain brake activated while changing working positions.

PPE, machine condition and fuelling in AFAG308

The leaflet lists PPE for climbing chainsaw users. The items are a helmet, eye protection, hearing protection, gloves, leg and groin protection to BS EN 381-5, protective boots and non-snag outer clothing. For the helmet, the Arboriculture and Forestry Advisory Group recommends a mountaineering-style helmet to BS EN 12492. The group recommends Type C leg protection for aerial work, with Type A possible where heat stress makes Type C impractical and a risk assessment justifies it. Each person should carry a personal first-aid kit with a large wound dressing, barrier gloves, plasters and a whistle.

A list of machine conditions applies before use. They include a working stop switch, an undamaged front hand guard and chain brake, a reduced kickback chain, and a means to attach a suitably rated or tear-away lanyard to the rear of the saw. Fuelling comes next, with a move of normally at least 4 m from the fuelling point before the saw is started. Maintenance follows the maker's handbook, and defects are reported without delay.

Chainsaw safety rules for tree work in other countries are compared on the guide to saw use aloft. The product standard for these saws is covered in the guide to the top-handle saw standard EN ISO 11681.

Sources