ArbNation Join free

Tree work safety in California: Title 8 Article 12, sections 3420 to 3428, and the Cal/OSHA checklist

California's tree work rules sit in Article 12 of the General Industry Safety Orders, sections 3420 to 3428. Cal/OSHA's checklist condenses sections 3420 to 3427 into 29 numbered items.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. Everything below is what the named codes and training bodies publish. It is not training and does not teach the work.

Article 12, Tree Work, Maintenance or Removal, is in Subchapter 7, General Industry Safety Orders, Title 8 of the California Code of Regulations. Section 3420 says it applies to work performed and equipment used in tree and ornamental palm maintenance and removal. Cal/OSHA, the Division of Occupational Safety and Health in the Department of Industrial Relations, publishes the text, a fact sheet, a checklist and a tree work safety page (updated March 2025). Cal/OSHA's consultation line is (800) 963-9424.

The nine sections

SectionTitleMain content
3420Scope and definitionScope; definitions such as qualified tree worker, drop zone, drop starting and proximity (10 feet of conductors rated 50 kV or less)
3421GeneralQualified tree worker directs each location; training; job briefing; rescue, first aid and CPR
3422Ropes and tree worker climbing equipmentStrength minimums for saddles and climbing lines; storage; inspection
3423Electrical hazards, generalInstruction on live equipment; 10-foot and 1-foot limits; line clearance trimmers; metal core rope
3424Mobile equipmentVehicles; aerial devices; brush chippers
3425Portable power hand toolsPower saws
3426Hand toolsCarrying and throwing tools; pole pruners and saws
3427Safe work proceduresClimbing and access; pruning and removal; felling; bucking; cabling and lightning protection
3428Stump cuttersGuards; protective equipment

Section 3421: general duties

Section 3421 requires an Injury and Illness Prevention Program under section 3203, and puts each work location where trimming, repair or removal is done under the direction of a qualified tree worker. Employees are trained in their job hazards, equipment and personal protective equipment, poisonous plants and harmful animals, pesticide and fertilizer work where it applies, and electrical hazards. Training is documented before an employee works without a qualified person observing. Refresher training follows a violation, an accident or near miss, or a new assignment with unfamiliar equipment.

A qualified tree worker holds a job briefing before each assignment. Section 3421(l) requires the employer to establish rescue procedures and provide emergency response training, with aerial rescue training for employees whose jobs may require it. Section 3421(m) requires first aid and CPR training, with at least two trained persons available for field work by two or more employees and new employees trained within 90 days of hire. Traffic control follows sections 1598 and 1599 of the Construction Safety Orders.

Section 3422: ropes and climbing equipment

Saddles must be approved under section 3206, and every component of a climbing system that carries the load has a minimum tensile strength of 5,000 pounds. Climbing lines are synthetic fiber with a rated tensile strength of at least 5,000 pounds (22.24 kN) and a diameter of at least 1/2 inch. The rule allows 7/16 inch (11 mm) line meeting the same strength and elongation figures when the maker names it suitable for tree climbing and the employee is trained. Maximum working elongation is seven percent at 500 pounds. Climbing lines are not spliced to repair them, and are not left unattended in trees when no qualified tree worker is on site. A line used for any other purpose, apart from raising and lowering tools, is not used again as a climbing line.

Section 3423: electrical hazards

Employees are instructed to consider equipment near them energized with potentially fatal voltages and never to touch it, directly or indirectly. They are also instructed on ground fault and step potential. Under 3423(b)(1), employees do not perform tree trimming within 10 feet of high voltage lines unless they are line clearance tree trimmers under Article 38 of the High-Voltage Electrical Safety Orders. Under (b)(2), a qualified tree worker trained in the listed skills may work within 10 feet but no closer than 1 foot of energized low voltage lines of 600 volts or less. Metal core rope is not used in a climbing system in proximity to energized equipment.

Section 3425: power saws

Section 3425(a) covers power saws. Chain saws are not drop started, and a saw is started on the ground or firmly held. A saw is not started aloft unless the area below is clear of personnel. Saws over fifteen pounds used in trees are supported by a separate line or tool lanyard, with two exceptions. A second point of attachment is used when operating a chain saw in a tree, unless the employer demonstrates a greater hazard from using one. A saw is not running while carried up a tree. The engine is stopped when carried more than 100 feet, and the chain brake is engaged when carried more than 10 feet. While a powered pole saw runs, no one but the operator is within 10 feet of the cutting head.

Section 3427: work procedures

Section 3427(a)(1) has a qualified tree worker visually inspect the tree, including the root collar, before climbing. It allows hoisting a qualified tree worker by crane, only when a tree cannot be safely accessed by climbing or an aerial device, under 10 listed criteria and special training. Employees aloft wear a saddle with at least two means of being secured and stay tied in from ascent to return to the ground. A second employee is present to give immediate help when anyone works higher than 12 feet, by ladder, climbing or aerial device.

Pruning and removal calls for an agreed communication method and a drop zone. For felling, a planned escape route comes before cutting. A notch and back cut set a hinge on trees over 5 inches in diameter, and notch depth does not exceed one-third of the diameter. Palm frond skirts are removed from the top down, with an exception for trimming from below on a competent worker's determination. Section 3427 lists nine factors to consider before felling, including lean, wind and decayed spots.

The Cal/OSHA checklist and fact sheet

The Tree Work Checklist runs sections 3420 to 3427 as 29 items, each tied to its section. They include a qualified tree worker on site (3421(b)), aerial rescue training (3421(l)), a saddle labeled 5000K (3422(a)), an escape route for felling (3427(c)(2)), and non-conductive pole pruners and saws (3426(b)(1)). The two-page fact sheet lists the sections and other rules that commonly apply: 1598, 1599, 2940.2, 2951, 3203, 3276 portable ladders, 3380, 3395 heat illness prevention, 3458 date palm fall protection and Article 105 noise exposure. It states that for full requirements, workers and employers refer to the Title 8 standards.

Other California tree work rules are on pages for heat rules and crane rules. Other states are compared in the guide to tree work rules by state and province.

Sources