Tree work words: traffic control and work zones
The US Manual on Uniform Traffic Control Devices and the UK Traffic Signs Manual define the zones, tapers and clearances around road works. Terms such as flagger, buffer space and longitudinal safety zone come from them.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
The US manual is the 2009 MUTCD with Revisions 1 and 2, from the Federal Highway Administration. It calls roadside work "temporary traffic control", or TTC. FHWA's knowledge page lists the 11th Edition with Revision 1, dated December 2025, as the current MUTCD; the terms and tables below are from the 2009 edition with Revisions 1 and 2, dated May 2012. The UK manual is Chapter 8, Part 1 (Design) of the Traffic Signs Manual, 2009. It uses "traffic management" and "road works".
United States terms
| Term | Meaning in the MUTCD |
|---|---|
| Temporary traffic control zone | An area of a highway where road user conditions are changed because of a work zone or incident, by the use of temporary traffic control devices, flaggers, uniformed law enforcement officers or other authorized personnel. |
| Flagger | A person who actively controls the flow of vehicular traffic into and/or through a temporary traffic control zone, using hand-signaling devices or an Automated Flagger Assistance Device. |
| Advance warning area | The section of highway where road users are told about the upcoming work zone or incident area. It may vary from a single sign or high-intensity rotating, flashing, oscillating or strobe lights on a vehicle to a series of signs. |
| Activity area | The section of highway where the work takes place. It is made up of the work space, the traffic space and the buffer space. |
| Work space | The part of the highway closed to road users and set aside for workers, equipment and material, and a shadow vehicle if one is used upstream. |
| Traffic space | The part of the highway where road users are routed through the activity area. |
| Buffer space | A lateral and/or longitudinal area that separates road user flow from the work space or an unsafe area. It might provide some recovery space for an errant vehicle. |
| Taper | A series of channelizing devices and/or pavement markings used to move traffic out of or into the normal path. |
Buffer spaces and tapers in Part 6C
Section 6C.06 of the MUTCD says neither work activity nor storage of equipment, vehicles or material should occur within a buffer space. A longitudinal buffer space may be placed in advance of a work space. A lateral one may separate the traffic space from the work space, or from such areas as excavations or pavement-edge drops. Table 6C-2 gives stopping sight distances that may be used for its length. They run from 115 feet at 20 mph to 305 feet at 40 mph, and 730 feet at 70 mph.
Section 6C.08 sets taper lengths as multiples of L. A merging taper is at least L, a shifting taper at least 0.5 L and a shoulder taper at least 0.33 L. A downstream taper is 100 feet per lane in Table 6C-3. A one-lane, two-way traffic taper is 50 feet at minimum and 100 feet at maximum. L equals the offset width times the square of the speed divided by 60 at 40 mph or less, and the offset width times the speed at 45 mph or more. The maximum distance in feet between devices in a taper should not exceed 1.0 times the speed limit in mph.
United Kingdom terms
| Term | Meaning in Chapter 8 Part 1 |
|---|---|
| Safety zone | The minimum-width space between moving traffic and the works, which workers and plant should not enter in the normal course of work and where materials should not be deposited. Traffic cones mark its outer boundary. |
| Lateral clearance | The sideways gap between the edge of the working space and the part of the carriageway traffic uses. On roads with a permanent limit of 50 mph or more it should be not less than 1.2 m. On single carriageways the manual's absolute minimum is 0.5 m. |
| Lead-in taper | The taper at the start of the works, ahead of the longitudinal safety zone. The manual sets its recommended length by the permanent speed limit and the width of the hazard including the safety zone. |
| Longitudinal safety zone | An open, unoccupied space between the end of the lead-in taper and the working space. It should be free of equipment, workers, materials and parked vehicles. |
| Exit taper | The taper at the far end of the works. The manual sets a minimum longitudinal exit clearance of its own, shown in Table 3.1. |
Chapter 8 Part 1 bases the longitudinal clearance on the permanent speed limit, not on a temporary reduced limit. Its Table 3.1 gives a minimum of 0.5 m at 30 mph or less, 15 m at 40 mph, 30 m at 50 mph, 60 m at 60 mph and 100 m at 70 mph. The desirable figures are higher: 10, 30, 50, 100 and 200 m. The minimum exit clearance runs from 0.5 m at 30 mph or less to 9 m at 60 and 70 mph. In Table 5.3, a hazard 1 m wide including the safety zone, on a single carriageway, has a lead-in taper of 13 m at 30 mph or less, 20 m at 40 mph and 25 m at 50 mph.
Chapter 8 Part 1 does not use the word flagger. The guide to traffic control manuals for roadside tree work covers the manuals themselves, and flagger and work zone traffic control cards covers training cards.
Sources
- US Federal Highway Administration, MUTCD 2009 with Revisions 1 and 2, Part 6 Section 6C (activity area, buffer space, tapers), read October 21, 2026
- US Federal Highway Administration, MUTCD 2009 with Revisions 1 and 2, Part 1 Chapter 1A (definitions), read October 21, 2026
- US Federal Highway Administration, MUTCD Knowledge page, 2009 MUTCD with Revisions 1 and 2, May 2012, and the note naming the 11th Edition as current, read October 21, 2026
- UK Department for Transport, Traffic Signs Manual Chapter 8 Part 1: Design, 2009, read October 21, 2026