ArbNation Join free

Trunk injection methods compared by delivery type, with wound-response research

Trunk injection puts a product into the sapwood through drilled holes, by capsule, low pressure, high pressure or implant. A 2011 green ash study sectioned 63 injection sites and found no infection, decay or structural damage in healthy trees.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

Trunk injection places an insecticide, fungicide or fertilizer inside the tree instead of on the foliage or in the soil. The University of Illinois describes microinjection as placing small amounts into the sapwood and cambium through holes drilled or punctured about 4 to 6 inches apart, near the root flare or in the lower few feet of the trunk. The tree then moves the material through its water-conducting system. This page sorts the delivery types by how the sources describe them.

Delivery types

Delivery types as the sources describe them
TypeHow it worksSource
Low-pressure microinjectionMaterial goes into the sapwood by low pressure. The Illinois note links uptake to the negative pressure in the xylem that transpiration creates.University of Illinois
Low-pressure microinfusionPorts are drilled with a 7 mm bit and fed from one pressurized bottle at 310 kPa.ISA journal study
High-pressure microinjectionMaterial is driven through a 7 mm port at 1379 kPa by an air-hydraulic device.ISA journal study
ImplantsSolid product goes into holes 9 mm wide and 3.2 cm deep, with no pressure. The study used 7 or 8 holes per tree.ISA journal study
Drilled holes with capsulesCapsules in drilled holes are one of the methods examined in the multi-university emerald ash borer FAQ, which notes that other devices make different wounds.Iowa DNR FAQ

The Illinois note lists the advantages of a closed system: little spray drift, a lower risk of spills, no wash-off and minimal exposure of the public. Its listed concerns are wound size and depth, the right number of capsules at the right depth, hole alignment, tree health after wounding and uneven distribution in the crown. Holes should never align vertically. Some trees do not accept large volumes this way: Illinois names American elm, which lacks porous xylem.

Timing and uptake

Illinois says injection is best done in fall or spring, when liquid moves fastest in the tree. Uptake usually takes 2 to 4 hours and depends on weather, tree age, tree health and soil temperature. It is best when soil is above 45 F and slower in stressed trees or dry soil. A maker's fact sheet from Arborjet, hosted by the St. Lawrence Eastern Lake Ontario invasive species partnership, gives its own figures for ash and emerald ash borer.

Figures declared in one maker's fact sheet
ItemDeclared figure
Treatment months, upper third of the countryMay through October
Injection heightBottom 18 inches of the tree
SpacingAbout 6 inches apart
Hole depth5/8 to 1 5/8 inch
Example doseAbout 1.5 ounces for a 10 inch diameter tree, for two years of protection
Spread through the treeHours to weeks; most trees protected within a few days

Wound-response research

Doccola, Smitley, Davis, Aiken and Wild published the study in Arboriculture & Urban Forestry in January 2011. They felled 16 green ash street trees in East Lansing, Michigan, in July 2009 and sectioned the trunks. Fourteen trees had been injected and two were untreated. The injected trees held 63 injection sites, treated with emamectin benzoate, imidacloprid or acephate by the three delivery types above. The trees averaged 27.6 cm in diameter.

  • No cracking, oozing or decayed tissue appeared at any of the 63 sites.
  • 76.2% of the sites were completely closed by new growth. Another 12.7% were closed except for a partly extruded plug. 11.1% were not completely closed.
  • Trees grew over more than 80% of the injured vascular surface within two years, whatever the insecticide.
  • Discoloured wood at the sites was still visible four years after injection, with no sign of decay.
  • The slow closers were two trees badly damaged by emerald ash borer. Closure rate followed the tree's ring growth.
  • The ports were pushed out of 13% of the injections.

The authors conclude that injection is well tolerated in healthy green ash. They used no water-injected controls. The Iowa DNR FAQ, written by University of Minnesota, Ohio State and Michigan State specialists, reaches the same view for relatively healthy, properly injected ash. It adds that other injection devices make wounds that differ from drilled holes, and that research has not thoroughly evaluated them.

Where injection fits among delivery routes

The FAQ says emamectin benzoate and specific imidacloprid formulations are injected into the base of the trunk. Other imidacloprid and dinotefuran products go on as a soil drench or soil injection, and dinotefuran can be sprayed on the lower five feet of bark. It says many emerald ash borer products are for licensed applicators only, and anyone applying a pesticide must follow the label. For trunk-injected products used as directed, it reports little risk to ground and surface water, because the material is placed inside the tree.

Sources