ArbNation Join free

US Forest Service National Tree Climbing Guide: chapters, scope and what it requires of its climbers

The 2015 National Tree Climbing Guide is the Forest Service's field manual for its own climbers, in 10 chapters and 88 pages. It rests on Forest Service Handbook 2409.17, chapter 50.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page describes what the named codes and training bodies publish. It is not training and does not teach the work.

Who the guide is for

The guide is a Missoula Technology and Development Center technical report, number 0567-2819-MTDC, dated April 2015. The Forest Service Research and Development record lists 11 authors and 88 pages. The front matter states the Forest Service developed it for its employees, its contractors and its cooperating federal and state agencies, and takes no responsibility for use by anyone else. Use of trade names is not an endorsement.

The National Tree Climbing Program Technical Advisory Group produced it, as authorized by Forest Service Handbook 2409.17, chapter 50. The group includes the national program leader, regional and station coordinators and technical advisors. Under section 51.08 of that chapter it recommends policy changes, sets criteria for equipment, approves new equipment and techniques, and hears appeals on climbing issues. It meets yearly.

The Forest Service's National Tree Climbing Program page says the program protects agency climbers and rests on recognized industry standards. It adds that the climbing techniques in the guide reflect the agency's history of work mostly in western conifers. Hardwood methods were explored later, largely for the Asian longhorned beetle survey run by the Animal and Plant Health Inspection Service. It holds that reading cannot make a safe climber: that takes training and practice.

The ten chapters

Chapters of the 2015 National Tree Climbing Guide
ChapterSubjectStarts on page
1Introduction: training, obtaining equipment, terms7
2Preparations for climbing: job hazard analysis, required protective equipment, teamwork, hazard assessment12
3Equipment: ropes, webbing, safety equipment, carabiners, helmets, slings17
4Knots31
5Tree entry methods: spurs, ladders, line installation, single and doubled rope technique, tree steps44
6Working in the tree: three point climbing, free climbing, lanyard use, handling materials60
7Rappel systems68
8Rescue, with sections on rescue from ladders, spurs, single rope, doubled rope and the upper crown74
9Using chainsaws in trees84
10Recommended publications87

Training and certification

Chapter 1 holds that only Forest Service employees with a valid tree climbing certification card issued by the agency may climb, and only with the techniques and equipment they are certified for. Applicants need American Red Cross first aid certification or equivalent. They sit a written or verbal exam on the guide, hazard reporting and equipment care. They then demonstrate knots, three point climbing with a lanyard, and an aerial rescue with an approved rappel system.

At least one certified Tree Climbing Instructor runs the training. The card runs to the end of the calendar year, three years after issue, unless revoked earlier. Work supervisors should promptly withdraw certification from a climber who is physically or mentally unable to climb safely, has an unsound safety attitude or shows unsafe habits.

Job hazard analysis and teams

Chapter 2 calls for a job hazard analysis for each assignment. It lists a check-out and check-in procedure, equipment inspection, radio contact with the local office or dispatch, and assessment of the environment and the tree. If radio contact is not possible from the site, another way to summon emergency help is to be set up before climbing.

The basic team is two certified climbers. One ground person can serve several climbers while keeping sight and unassisted voice contact with all of them. Every team climber has to be qualified in every part of the assignment, so as to perform a rescue, and to hold first aid training equal to a basic Red Cross course. Team members check each other's equipment. The ground person stays out from directly under a climber unless the climber clears it.

Required protective equipment for all climbing is a harness, a climbing helmet, a long sleeved shirt and sturdy pants, and eye protection. Hearing protection is listed for power tool use. Gloves are recommended, with sturdy gloves called a must for rappelling.

Hazard limits the guide sets

The guide bars climbing under certain conditions unless the job hazard analysis mitigates them. These include winds over 25 mph or gusts, light too low to finish the climb in full daylight, a close lightning storm, and cold low enough to impair the fingers. A tree within 10 feet of energized conductors is barred to anyone not qualified as a line clearance arborist.

Chapter 2 also lists tree hazards, among them slippery moss and lichen, brittle limbs, dead branches and stubs, weak branch unions, poor architecture, forked boles and spiked tops. Above the 4-inch diameter point in conifers it requires a safety line.

Rescue and chainsaws

Chapter 8 opens by saying all certified climbers should be equipped and trained to render emergency care if a climber becomes incapacitated in a tree, with training that includes first aid and removal of the climber from the tree. It describes suspension trauma, with death possible in as little as five minutes, and a rescue pack reserved for rescue purposes only, plainly marked, with its contents listed on a tag or inside the pack. Its recommended items include a first aid kit of 10 units at minimum.

Chapter 9 treats chainsaw use aloft as something to be justified and recorded in the job hazard analysis, with the smallest saw that does the job. It sets four endorsement categories: cavity creation (EC-1), hardwood pruning (EC-2), conifer pruning (EC-3) and advanced rigging with heavy wood removal (EC-4). Endorsements last three years, on top of a sawyer certification and a climber certification. The chapter names ANSI Z87.1 eye protection, ANSI Z89.1 Type II or UIAA helmets, and leg protection to Forest Service Specification 6170-4 or ASTM F-1897. It calls for two attachment systems with one cut resistant, and a tethered saw.

The saw directive that replaced Handbook text

The final directive for the National Saw Program was published in the Federal Register on July 19, 2016, effective that day. It revised Forest Service Manual 2350, to be codified at section 2358, and removed duplicate text from Forest Service Handbook 6709.11, section 22.48. The directive will supersede duplicative text in chapter 20 of that handbook and in all Forest Service regional supplements to it. Sawyers will receive one or more of six skill level certifications, and a National Sawyer Certification Card documents the level. Current first aid and CPR training are among the specified qualifications. The guide's chainsaw chapter predates that notice. The program itself is covered in our page on Forest Service sawyer certification.

Sources