Using a chainsaw at height: the UK industry code, HSE guidance and the US OSHA wording compared
Britain's industry code asks for a certificate of competence before a chainsaw goes aloft, and OSHA's tree-work paragraph gives a 15-pound line rule for saws used in trees. Both are printed in their own words below.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
Britain's tree-work code, HSE and OSHA publish the wording summarised here. It is not training and does not teach the work.
The UK industry code
The Industry Code of Practice for Arboriculture: Tree Work at Height, second edition, May 2020, covers work methods that include ladders, MEWPs, cranes and mobile scaffold towers. Section 3.7 deals with training. It states that operators who wish to use a chainsaw for work at height should have received appropriate training and obtained a relevant certificate of competence or national qualification. The exception is someone who is undergoing that training and is adequately supervised.
The same section lists when refresher or update training is expected. The cases are a change in tasks or risks, new equipment, a change in the system of work, and skills that are not regularly used. It adds safety-critical tasks that depend on proficiency being kept up, such as aerial rescue.
Section 3.9 sets out a risk hierarchy for tools. Selection rests on the hazards of the equipment (noise, vibration, moving parts), the nature of the work, and the skill and experience of the operator. The code gives the examples of a pruning saw, a pole saw, a lightweight top-handled chainsaw and a larger rear-handled chainsaw.
For cutting tools in the tree, the code requires all measures to eliminate or minimise the chance of striking the systems that connect the operator to the anchors. For hauling, it calls it important to secure tools in the tree or to the operator's harness before they are disconnected from the hauling line.
MEWPs in the same code
Section 3.3.5.5 lists what operators must be able to do when a task involves a MEWP. That covers identifying the drop zone, understanding the limits of the machine's working envelope, carrying out appropriate and accurate cutting techniques, and positioning the platform so branches and tree sections cannot touch its components. Section 3.8.3 adds that an operator working from the platform may need a work restraint system. Section 3.8.3.1 lists wind speed above the platform's limit, or wind acting adversely on the trees, among the points for the site plan.
HSE guidance
The HSE page Working with chainsaws states that by law, chainsaw operators must have received adequate training relevant to the type of work they undertake. They are also required to wear appropriate chainsaw protective clothing whenever they use a chainsaw. The free leaflet Chainsaws at work, INDG317 (revision 2, 2012), is the HSE guide for employers and workers.
INDG317 covers portable hand-held petrol chainsaws. Its contents list includes fitness to operate, training and competence, selecting and maintaining a chainsaw, lone working, first aid, tree felling, and working with a chainsaw off the ground. The HSE page also links a separate leaflet on top-handled chainsaws, AFAG308, and pages on working at height.
On experience, the HSE page notes that people holding only CS 30/31 with little additional experience can quickly find themselves in situations outside their experience and skill base. It names larger and awkward fells and the unique hazards of arboricultural operations in gardens.
For the UK awards that cover the training side, see the site's pages on the award for chainsaw use from rope and harness and the award for chainsaw use from a MEWP.
OSHA wording in the United States
Paragraph (r)(5) of 29 CFR 1910.269 covers gasoline-engine power saws in line-clearance tree trimming near electric lines. It states that these operations meet the requirements of 1910.266(e) and then lists more.
| Item | Wording restated |
|---|---|
| Saw over 15 pounds | A power saw weighing more than 6.8 kilograms (15 pounds, service weight) used in trees is supported by a separate line. Exceptions: work from an aerial lift, and topping or removing where no supporting limb will be available |
| Controls | A control returns the saw to idling speed when released, and a clutch is adjusted so it does not engage the chain drive at idle |
| Starting | A power saw is started on the ground or where otherwise firmly supported. A note to the paragraph records that 1910.266(e)(2)(vi) prohibits drop starting of chain saws |
| Other people | A power saw engine is started and operated only when all employees other than the operator are clear of the saw |
The chain saw paragraph of 1910.266(e)(2), the logging standard, adds a chain brake on each saw placed into initial service after the effective date of that section, and a continuous pressure throttle control on each gasoline-powered saw. It also requires the saw to be started with the chain brake engaged, and says a chain saw shall not be used to cut directly overhead. It requires the operator to be certain of footing and not to cut in a position that causes loss of balance or grip.
Where the two sets differ
The UK code ties chainsaw use aloft to training and a certificate, and ties tool choice to the operator's experience. The OSHA paragraphs tie it to saw weight, controls, starting position and who stands clear. On the MEWP, the UK code lists drop zone and working envelope, while the US paragraph carves aerial lift work out of the separate-line rule.
Sources
- Arboricultural Association, Lantra and partners, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, read October 16, 2026
- Health and Safety Executive, Working with chainsaws (tree work), read October 16, 2026
- Health and Safety Executive, Chainsaws at work INDG317 (rev2), 2012, product page, read October 16, 2026
- 29 CFR 1910.269 Electric power generation, transmission, and distribution, paragraph (r)(5), Electronic Code of Federal Regulations, read October 16, 2026
- 29 CFR 1910.266 Logging operations, paragraph (e)(2), Electronic Code of Federal Regulations, read October 16, 2026