Wood chip pile self-heating and fires: what COFORD, WPAC and Bioenergy NZ print
A COFORD note, a Wood Pellet Association of Canada sheet and a Bioenergy NZ note describe how stored chips heat themselves, from 45 degrees C to a self-ignition point near 250 degrees C. Moisture limits differ between them.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
COFORD, at the Irish Department of Agriculture, Food and the Marine, published a note in 2016 on health and safety when using wood chips as fuel. It opens by calling chips as safe as oil, gas or even coal as a fuel, and in some cases safer, when simple rules are followed. The Wood Pellet Association of Canada (WPAC) fibre pile sheet of March 31, 2021 and a Bioenergy Association of New Zealand technical note of May 2021 cover the same hazard for industrial piles.
How a chip pile heats itself
COFORD describes the sequence. Bacteria begin to consume the wood, using oxygen and releasing carbon dioxide, water and heat. Fungi follow and release far more heat, taking the pile to about 45 degrees C. Heat-loving fungi then take it to 70 to 80 degrees C, which kills the fungi and bacteria. That is far below the self-ignition temperature of wood, which COFORD puts at around 250 degrees C. Chemical oxidation takes over after the biological stage and can bring the pile to ignition.
WPAC describes the same stages with different numbers. Heat accumulates to around 60 degrees C because air passage is limited and woody biomass conducts heat poorly, and at 80 degrees C and higher most biological activity ceases. Later heat comes from water transport, hydrolysis, chemical oxidation and charring, and dry matter loss and lost fuel quality may end in spontaneous ignition.
COFORD says a pile of chips at 45 percent moisture with enough nutrients can reach 60 to 80 degrees C in as little as 24 hours. Pure wood chips with no bark or needles heat very slowly or not at all, because they lack nutrients for microbes. Bark, leaves and needles supply them. In very wet, nutritious chips such as short rotation willow, COFORD reports dry matter losses above 3 percent per month. In forest chips above 35 to 40 percent moisture it expects about 1 percent per month.
Figures that differ between the sources
| Topic | COFORD (2016) | WPAC (2021) |
|---|---|---|
| Moisture for storing chips | Chips kept more than 2 to 3 weeks should be under 35 percent moisture | Dry fuels under 20 percent moisture avoid microbial growth |
| Pile size | Piles that self-ignite are usually very large, over 1000 cubic metres loose volume | Elongated stacks with base width twice the height. Typical heights are 15 m for clean chips and chipped forest residue, 7 m for bark and 6 m for sawdust |
| Peak biological heat | 70 to 80 degrees C | Around 60 degrees C |
| Compaction | Piles are often compacted by driving across them | Avoid compacting by running heavy equipment on the material |
COFORD's indicative storage periods by moisture content come from trial results and long experience:
| Moisture content | Indicative storage period |
|---|---|
| 0 to 15 percent | Very long periods, several years |
| 16 to 25 percent | Several years |
| 26 to 35 percent | Up to a year |
| 36 to 45 percent | Months |
| 46 percent or more | Days to weeks, maximum 1 month |
Self-ignition conditions
COFORD says self-ignition of chip piles occurs only in exceptional cases, mostly in very large piles where several conditions meet. The piles are often compacted, and they hold at least some wet chips. In almost all cases a metal object is tied to the start of the fire, because metal is the catalyst. Examples are machinery parts or chipper knives that ended up in the pile. An irregular pile shape lets rain collect in valleys and raise moisture there.
Surface fires are rarer. COFORD reports them on very dry chips, such as recycled wood, where sparks from equipment or another outside cause is usually behind the fire.
Detection and fire response in the WPAC and Bioenergy NZ texts
WPAC lists temperature monitoring at several points in the bulk, and measuring carbon monoxide in the air above the fuel surface as one possible way to detect activity in the fuel bed. Multi-gas detectors and electronic nose detectors are others. The first sign of self-heating is often a sticky, irritating smell. WPAC names firefighting as the step when fire smell or smoke, not water vapour, comes from the pile. Its ignition-source list includes hot work, spark-forming impurities, equipment above 100 degrees C, motor overload and friction in conveyors.
Bioenergy NZ describes smouldering pockets that can last for months and leave gaps that can collapse under any weight. It lists thermal imaging cameras for early hot-spot detection and says workers do not climb on a pile suspected of self-heating. The note calls for trained firefighters or the local fire department to expose and extinguish smoulders.
COFORD describes smouldering inside a pile as a blue haze and a distinct smell of burning wood. It says water pumped onto the pile spoils sound chips. Its method is to pull sound chips away from the burning area, spread them to cool, and then put water on the fire. A surface fire on very dry chips is usually contained and left to burn out, which can take several days or more than a week.
Enclosed stores and carbon monoxide
COFORD does not give a carbon monoxide figure. It describes oxygen depletion in silos: wood still respires after chipping, and microbes use oxygen, so an unventilated silo runs short. COFORD says one person should not work alone in a silo, even after ventilation. A Massachusetts FACE report on carbon monoxide inside a wood chip fuel hopper has its own page.
Sources
- COFORD, Department of Agriculture, Food and the Marine (Ireland), P. D. Kofman, Health and safety aspects of using wood chips as a fuel, Processing/Products No. 41, revised 2016, read October 16, 2026
- Wood Pellet Association of Canada, Best Practice Fibre Pile Management, S. Sokhansanj, March 31, 2021 (hosted by BC Forest Safety Council), read October 16, 2026
- Bioenergy Association of New Zealand, Technical Note TNSB80, Fibre pile management best practice, May 2021, read October 16, 2026