ArbNation Join free

Working alone in British Columbia: OHS Regulation 4.20.1 to 4.23 and check-in intervals

British Columbia's OHS Regulation sections 4.20.1 to 4.23 cover workers assigned to work alone or in isolation. The employer identifies hazards and runs a written well-being check with set intervals.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. WorkSafeBC publishes the Occupational Health and Safety Regulation, its OHS Guidelines for Part 4 and a working alone topic page. The sections on working alone or in isolation run from 4.20.1 to 4.23. Section 4.20 itself is about impairment.

At a glance

Working alone or in isolation in OHS Regulation Part 4
SectionSubject
4.20.1Definition: circumstances where assistance would not be readily available in an emergency or if the worker is injured or in ill health
4.20.2Hazard identification, elimination and control before a worker is assigned
4.21Written procedure for checking the well-being of the worker
4.22Training for the worker and for anyone assigned to check on the worker
4.22.1Late night retail premises, with late night hours defined as 11:00 p.m. to 6:00 a.m.
4.23Procedures reviewed at least annually

The definition and what assigned means

Section 4.20.1 defines to work alone or in isolation as working in circumstances where assistance would not be readily available to the worker in case of an emergency or in case the worker is injured or in ill health. The OHS Guidelines add four questions for readily available assistance. They ask who is nearby, whether those people would be aware of the need, whether they would be willing to help, and whether help would come in a reasonable time.

The guideline G4.20.1 notes that a phone, radio or personal alarm does not by itself meet the test, and a "person check" system alone is also unlikely to meet it. If a worker cannot be seen or heard by people able to help in a timely manner, the worker should be regarded as working alone or in isolation.

The requirements apply to a worker who is assigned to work alone. G4.20.2 describes that as a worker directed or expected to work alone during a scheduled or predetermined period, such as a specified shift. It lists a forestry worker among the examples of work with hazards and no regular interaction with other people.

Hazard identification and control

Under section 4.20.2 the employer must identify any hazards to the worker before the assignment. Before the work starts, the employer must take measures to eliminate each hazard. Where elimination is not practicable, the employer must minimise the risk to the lowest level practicable using engineering controls, administrative controls or both.

G4.20.2 names administrative controls such as arranging schedules so that hazardous work, for example work that presents a falling hazard, is done while more than one worker is present. It also names a rule that the worker contacts the person responsible for checking before and after the expected completion time of a possibly hazardous activity.

The check-in procedure

Section 4.21(1) requires a written procedure for checking the well-being of a worker assigned to work alone or in isolation. The procedure must include the time interval between checks and what to do if the worker cannot be contacted, including provisions for emergency rescue. A person must be designated to make contact at predetermined intervals, and that person must record the results.

A check at the end of the work shift is required on top of the checks at regular intervals. The procedure and its intervals are developed in consultation with the joint committee or the worker health and safety representative. The intervals are also developed in consultation with the worker assigned to work alone.

WorkSafeBC's note to the regulation says high risk activities require shorter time intervals between checks. It prefers visual or two-way voice contact. Where that is not practicable, a one-way system is acceptable if it lets the worker call or signal for help and sends a call for help when the worker does not reset the device after a predetermined interval.

G4.21 lists call-in systems, externally monitored panic alarm devices and internally monitored panic alarm devices for populated areas. For remote locations it lists wireless satellite hand-held alerting and tracking devices, satellite phones, radio transmitters and crew contact. Timber cruising and beetle probes are among its examples of remote work.

The guideline describes crew contact as five elements. They are a predetermined meeting place or other means of contact, a predetermined time, and information on expected routes and areas. The other two are a procedure if a worker does not make contact and a plan to find a missing worker. A non-worker, such as a family member, may be the contact person only where that is a reasonable means of doing effective checks, usually in low and negligible risk cases.

Training and annual review

Section 4.22 requires that the worker, and any person assigned to check on the worker, be trained in the written procedure. Section 4.23 requires the procedures to be reviewed at least annually. Review comes sooner after a change in work environment arrangements that could adversely affect the worker's well-being or safety. It also comes sooner after a report that the procedures are not working effectively.

WorkSafeBC's working alone page adds that lone workers must be able to get assistance if they are injured or there is an emergency. It lists a handbook for small business, published in June 2012.

Sources