Aerial lift rescue plans and emergency lowering controls: OSHA, WorkSafeBC and HSE
Britain's Work at Height Regulations 2005 put emergencies and rescue inside work planning. HSE names ground personnel to lower the platform, and OSHA and WorkSafeBC require lower controls that override the platform's.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work. Three bodies cover getting a person down from an aerial lift: HSE and the Work at Height Regulations 2005 in Great Britain, OSHA in the United States, and WorkSafeBC in British Columbia.
At a glance
| Body | What it publishes on rescue and lowering |
|---|---|
| Work at Height Regulations 2005, regulation 4 | Planning of work at height includes planning for emergencies and rescue |
| HSE, information sheet GEIS6 | The rescue plan names trained site personnel who lower the platform from the ground controls or emergency descent system |
| OSHA, 29 CFR 1910.67 | Lower controls override upper controls; lower controls are not operated without the person in the lift's permission, except in an emergency |
| WorkSafeBC, OHS Regulation 13.26 | An overriding lowering control lets a worker at the lower controls stop and lower the platform in an emergency |
Great Britain
Regulation 4(1) of the Work at Height Regulations 2005 obliges every employer to see that work at height is properly planned, appropriately supervised and carried out as safely as is reasonably practicable. Regulation 4(2) adds that planning includes planning for emergencies and rescue. The regulation does not mention aerial lifts by name.
HSE's information sheet GEIS6 on mobile work platforms (MEWPs), first published in October 2014, fills in the plan. The emergency and rescue plan should identify nominated, trained, site-based personnel. They would lower the platform from the ground controls or the emergency descent system at the base of the machine if the operator in the platform runs into difficulty. Those people should be in the familiarisation for each machine on site and get the chance to practise the rescue at regular intervals.
The sheet says the plan should also carry call-out details for a service engineer or other competent, authorised person who can lower the platform after an emergency or a machine malfunction. Familiarisation is listed as covering the manufacturer's instructions, the controls, each safety device and the emergency lowering procedures, and the sheet says it should be recorded. People lifted by the machine also need instruction in fitting and using the harness, lanyard and rescue equipment.
HSE's construction safety page on MEWPs names entrapment, overturning, falling and collision as the main hazards. In entrapment the operator can be trapped against the platform controls, unable to stop the machine. It advises having a plan for rescuing someone from the platform and practising it, so that someone on the ground knows what to do in an emergency and how to operate the ground controls.
United States
OSHA's rule for vehicle-mounted work platforms, 29 CFR 1910.67, sets the control layout in paragraph (c)(2)(ix). Articulating and extensible boom platforms built mainly as personnel carriers carry both platform (upper) and lower controls. Upper controls sit in or beside the platform, within easy reach of the operator. Lower controls provide for overriding the upper controls, and all controls are plainly marked for their function.
The paragraph then covers use of the lower controls: they are not operated unless permission has been obtained from the employee in the lift, except in case of emergency. Other paragraphs in the section require lift controls to be tested each day before use, and only trained persons to operate an aerial lift. A personal fall arrest or travel restraint system attached to the boom or basket is worn when working from the lift. The rule contains no written rescue plan requirement.
British Columbia
WorkSafeBC's OHS Regulation Part 13 deals with work platforms, including the boom-type platforms it calls EWPs. Section 13.26 sets the controls: identified by function, hold-to-run, protected against inadvertent operation, and fitted with an emergency stop that is within easy reach, labelled STOP and coloured red for each set of controls. They also include an overriding lowering control, marked as such, that lets a worker at the lower controls stop and lower the platform in an emergency.
| Section | Part 13 provision |
|---|---|
| 13.21 | The maker's operation manual is available at the workplace; if it is missing, the equipment is not used until it is obtained or an engineer supplies written instructions |
| 13.23 | A vehicle-mounted EWP is inspected at least every 12 months and certified in writing by the maker or a professional engineer |
| 13.33 | A person on an EWP wears a personal fall arrest system secured to a suitable anchorage, with an exemption for scissor lifts on firm level ground with guardrails and chains in place |
HSE's sheet describes nominated, trained, site-based personnel. OSHA and WorkSafeBC describe the equipment: a lower control that overrides the platform.
Sources
- U.S. Code of Federal Regulations, 29 CFR 1910.67 Vehicle-mounted work platforms (aerial lifts), via eCFR, read October 19, 2026
- WorkSafeBC, OHS Regulation Part 13 Ladders, scaffolds and temporary work platforms, sections 13.21, 13.23, 13.26 and 13.33, read October 19, 2026
- legislation.gov.uk, The Work at Height Regulations 2005 (SI 2005/735), regulation 4, read October 19, 2026
- HSE, General Information Sheet 6, the selection, management and use of MEWPs, first published October 2014 (PDF), read October 19, 2026
- HSE, Construction safety topics: MEWPs, read October 19, 2026