ArbNation Join free

ANSI A92.24 operator training: OSHA 1910.67 and the North Carolina state programs

OSHA's aerial lift rule has one training sentence. North Carolina's state MEWP program and NC State's own program build on ANSI A92.22 and A92.24 with theory, hands-on evaluation, occupant and supervisor training.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. ANSI A92.24 is sold by ANSI. This page draws on OSHA's rule at 29 CFR 1910.67 and two North Carolina public programs built on A92.22 and A92.24. One is the state Office of State Human Resources model program, effective April 1, 2021. The other is the NC State University Environmental Health and Safety program.

OSHA's training sentence

Paragraph (c)(2) of 29 CFR 1910.67, on extensible and articulating boom platforms, states that only trained persons shall operate an aerial lift. The rule has no course length, curriculum or card. It also requires aerial lifts acquired on or after July 1, 1975 to follow the 1969 standard, ANSI A92.2.

The standards named

The state model program's list of related ANSI standards includes A92.2-2015 on vehicle-mounted aerial devices, A92.20-2018 on design and test methods, A92.22-2018 on safe use, and A92.24-2018, Training Requirements for Operators of Mobile Elevated Work Platforms (MEWPs). The NC State program prints the A92.24 title differently. Its version covers the use, operation, inspection, testing and maintenance of MEWPs.

Operators, supervisors and occupants

The state model program says supervisors, operators and occupants all receive appropriate training before lift use, and stay trainees until trained and qualified on a specific lift. It defines an occupant as a person on the platform who is not the operator, and a supervisor as the person who monitors operator performance. A qualified person is someone with a recognised degree, certificate, professional standing or skill who has shown, by knowledge, training and experience, the ability to deal with the subject. Training is instruction that makes the trainee a qualified person for the task, including its hazards.

  • Training has theory (classroom or online), practical hands-on operation, and an evaluation.
  • Theory covers safe use as defined in A92.22, stability factors, pre-start inspection, wind and weather, controls including emergency descent, and the requirement for familiarization on top of training.
  • Hands-on training has the trainee show proficiency in walk-around, major components, pre-start inspection, route planning, setting up, controls, and parking and securing.
  • Operators sit an exam at the end of training on the MEWP they were trained on.
  • Supervisors are trained in choosing the right MEWP, the rules that apply, the work and its hazards.
  • Occupants are trained in fall protection and its anchors, how their actions affect stability, and emergency lowering to the extent needed to bring the lift down if the operator cannot.

Who trains, and the paperwork

The state program says all training is delivered by a Qualified Trainer experienced with the classification of MEWP, and the curriculum states that it covers only the classifications in the course. Proof of training names the training entity, the trainer, the MEWP classification, the completion date, the trainee and the period the training is valid, if any. NC State's program adds that operators may run only the class of MEWP they were trained on.

NC State splits operator training in two parts. Part 1 is theory and hazard awareness, classroom or online. Part 2 is hands-on training and evaluation. Trainees with limited experience can work under the direct supervision of a qualified operator, and are not counted as qualified operators until Part 2 is done.

Familiarization and retraining

The state program expects the operator of an unfamiliar MEWP to read the manual, walk around the machine, learn the controls and understand its limits. It lists situations for retraining: no use of the lift within a year of training, expiry of the valid training period, skills that have slipped, technology that is new or differs greatly, and an accident or near miss. The state program calls retraining every two years highly recommended.

Sources