Anti-vibration mounts: what makers, HSE and HSA publish about wear and vibration exposure
HSE and the Irish HSA both list the anti-vibration mounts among the parts of a petrol saw to inspect for damage. Maker manuals call the same parts elements or damping units and link vibration to hand problems.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named regulators and makers are described here as published. It is not training and does not teach the work.
What the mounts are
Maker B's manual describes a vibration damping system that reduces the transfer of vibration between the engine unit and cutting equipment on one side and the handle unit on the other. The body of the saw, cutting equipment included, is insulated from the handles by vibration damping units. Maker A's manual puts the same idea in one sentence: the condition of the anti-vibration elements influences vibration behaviour. Maker C's manual lists an anti-vibration device among the standard features of its saw.
HSE's leaflet INDG317, Chainsaws at work, shows the anti-vibration mounts on a labelled drawing of a rear-handled chainsaw, next to the chain catcher and the rear chain breakage guard.
Wear checks
| Source | Wording on the mounts |
|---|---|
| HSE, INDG317 | Operators report any damage or excessive wear found in daily checks. The list includes the anti-vibration mounts, with the on and off switch, chain brake, chain catcher, silencer and guide bar |
| HSA, IFSG 301 | A chainsaw is used only if the front hand guard or chain brake, the chain catcher and the anti-vibration mounts are undamaged and functional. The anti-vibration rubbers are inspected frequently and replaced as the maker's handbook specifies |
| Maker A manual | The anti-vibration elements are inspected periodically. The maintenance chart has a row for them marked "check" |
| Maker B manual | The vibration damping units are checked regularly for cracks or deformation and for secure attachment to the engine unit and the handle unit. The pre-use list has the anti-vibration system working and undamaged. The maintenance schedule puts the check of the damping elements in the weekly column |
| Maker C manual | The anti-vibration device appears in the list of standard features. The manual prints no separate wear check for it |
The intervals differ by source. HSE gives daily, HSA frequently, Maker B weekly and Maker A periodically. HSA sends the reader to the maker's handbook for replacement.
HSE on the exposure
INDG317 says chainsaws expose operators to high levels of noise and hand-arm vibration. These can lead to hearing loss and to conditions such as vibration white finger. The leaflet lists buying low-noise and low-vibration chainsaws, with anti-vibration mounts and heated handles as examples, among the controls it names. It also says proper maintenance is necessary for protection against ill health from excessive noise and vibration.
HSE publication L140, second edition, July 2019, sets out an employer's duties under the Control of Vibration at Work Regulations 2005 as they relate to hand-arm vibration. Its aim is to prevent diseases such as hand-arm vibration syndrome and carpal tunnel syndrome. It covers risk assessment, controlling exposure and health surveillance. HSE's hand-arm vibration hub page links to the exposure calculator, the risk assessment guidance and the regulations, and prints no exposure limits itself. Exposure limits for chainsaw users have their own guide, hand-arm vibration limits for chainsaw users.
Maker warnings on vibration
Maker A's manual names vibration-induced circulation problems in the hands, called white finger disease. It gives no general figure for time of use, because that depends on several factors. Warm gloves and work breaks lengthen the usable period. Poor circulation, low outside temperatures and a tight grip on the handles shorten it. Users who work regularly are told to watch their hands and fingers, and to seek medical advice if tingling appears.
Maker B's manual says cutting hardwoods creates more vibration than cutting softwoods, and that blunt or faulty cutting equipment raises the vibration level. Overexposure can lead to circulatory or nerve damage in people with impaired circulation. Maker C's manual links vibration and cold to tingling and burning in the fingers, followed by loss of colour and numbness. It also lists carpal tunnel syndrome among the conditions some believe prolonged vibration may contribute to. The guide on hand-arm vibration syndrome covers the condition itself.
Sources
- HSE, Hand-arm vibration hub page, updated January 20, 2026, read October 19, 2026
- HSE, The Control of Vibration at Work Regulations 2005 (L140), second edition, July 2019, read October 19, 2026
- HSE, Chainsaws at work INDG317 (rev2, January 2013), read October 19, 2026
- Health and Safety Authority (Ireland), Irish Forestry Safety Guide IFSG 301 Using Petrol-Driven Chainsaws, October 2018, read October 19, 2026
- Chainsaw maker A, instruction manual, document 0458-153-8321-C (English), read October 19, 2026
- Chainsaw maker B, operator's manual (English), read October 19, 2026
- Chainsaw maker C, operator's manual, January 2024 edition, read October 19, 2026