ArbNation Join free

Arboricultural Association Safety Guide 2, Use of Tools in the Tree: what it covers

Safety Guide 2 is a seven-page Arboricultural Association checklist, dated December 2020, for anyone using tools in tree work. It runs from planning to tape slings and sits beside HSE leaflet AFAG308.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named codes and training bodies are described here as published. It is not training and does not teach the work.

The leaflet

The Arboricultural Association (AA) lists Safety Guide 2 second in its series of five. Each guide is derived from the Technical Guide of the same title, and the AA built the series by compiling the safety checklist that opens each technical section. Guide 2 comes from Technical Guide 2, Use of Tools in the Tree.

The leaflet calls its notes good practice that is not compulsory. It states that it is not a substitute for adequate training or for the full Technical Guide. The key principles of the Industry Code of Practice (ICoP) for tree work at height must be adopted when it is used. Anyone using tools in tree work can use it as outline guidance to check that operators are following industry guidance.

The AA's series page was posted on 15 December 2020 and last modified on 26 November 2021. The leaflet itself carries a December 2020 date.

Access first, then tools

Guide 2 says a decision must be made on whether to climb or to work from the ground or a MEWP. It sends readers to the ICoP for that decision: climbing only when it is not reasonably practicable to do the work from ground level or from a platform, in that order. Many of the techniques can be carried out whether the tree is reached by MEWP or by climbing.

Checklist sections

Every section is a list of questions with Yes, No and N/A columns. The leaflet closes with a notes page for the date, location, observer, who is observed, comments and actions, so the sheet can record an audit.

AA Safety Guide 2 checklist sections and the questions in each
SectionQuestionsWhat the questions ask about
2 Planning11Recorded risk assessment, emergencies, rescue provision, time allowed, wildlife, biosecurity, drop zone, command-and-response communication
3 Work quality3Reading work specifications, meeting the instructing party's requirements, evidence such as site safety audits
4 Work equipment4A suitable range of equipment, selection to minimise operator risk, operator training
5 Inspection and maintenance4Machinery free from defect, safety features intact, inspection, maintenance to the manufacturer's guidance
6 PPE for cutting tools4PPE matched to the equipment, labelling to standards, first aid, hand hygiene
7 Equipment hauling6Accidental release, communication with ground staff, clear drop zone, safe working loads, operator strain
8 Securing and carrying equipment5Tool lanyards, approved harness connection points, blades covered, accidental release
9 Handling tools in the tree4Risk hierarchy, operator position, reactive forces on the fall protection system, equipment taken with severed sections
10 Chainsaw use4Warm-up and checks, starting, two-handed use as the norm, justification for one-handed use
11 Cutting methods4Explaining the method, factors that move a branch or section, control of severed sections
12 Trapped cutting equipment3Procedures for trapped tools, a handsaw carried by the climber
13 Pull and tag lines3Pre-use checks, length, strength, attachment, clear drop zones
14 Tape slings2Appropriate circumstances, pre-use checks, rigging designation, safe working load

Beside HSE leaflet AFAG308

The Health and Safety Executive (HSE) publishes AFAG308, Top-handled chainsaws, revision 2 of April 2013, first published in December 2008. It covers petrol-powered top-handled saws for off-ground arboricultural work. HSE states that the work should be done by a trained and competent climber with chainsaw experience, or by a trainee under supervision who is competent on the ground. It also states that top-handled saws suit off-ground work only and that rear-handled saws are used on the ground.

The two documents meet on one-handed use. Guide 2 asks whether two-handed use is the norm and whether any one-handed use is justifiable. AFAG308 advises gripping both handles wherever possible and says one-handed use raises the risk of injury if the saw kicks back, skates or bounces. It limits one-handed use to cases where one hand is needed to hold a stable position and the saw is at extended reach. Poor work positioning is, in its words, not an acceptable reason.

The same overlap shows on lanyards and trapped saws. AFAG308 says a saw may be attached to the harness by a suitably rated or tear-away lanyard, but not where it could be trapped or taken with a severed section. Guide 2 asks about tool lanyards that are rated and free from defect, and about measures to prevent equipment being taken with severed sections.

AFAG308 lists a helmet, preferably a mountaineering style under BS EN 12492. Eye protection falls under BS EN 1731 or BS EN 166, hearing protection under BS EN 352, leg protection under BS EN 381-5 and boots under BS EN ISO 20345. It recommends Type C leg protection for aerial work and allows Type A where a risk assessment justifies it. Guide 2 asks whether PPE is labelled to show it was made to the relevant standards.

HSE adds that its guidance is not compulsory unless stated, and that following it will normally be enough to comply with the law. AFAG308 is to be read with AFAG401, AFAG402 and AFAG403.

Where the leaflet points next

Guide 2 ends with a reading list of Technical Guides 1 to 5, FISA 802 on emergency planning and FISA 805 on training and certification. Related reading: the guide to Arboricultural Association Safety Guides 1 to 5, the guide to top-handled chainsaws and the guide to FISA and AFAG leaflets.

Sources