ArbNation Join free

Articulating boom cranes: OSHA Subpart CC scope, the tree work exclusion and the 2,000 pound provisions

OSHA's crane standard names knuckle-boom cranes in its scope, then excludes tree trimming and tree removal work in 1926.1400(c)(13). A separate section covers equipment rated 2,000 pounds or less.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The text is 29 CFR 1926 Subpart CC, Cranes and Derricks in Construction, as OSHA publishes it.

At a glance

Subpart CC provisions that touch articulating boom cranes
ProvisionWhat it prints
1926.1400(a)Scope includes articulating cranes, such as knuckle-boom cranes, and commercial truck-mounted and boom truck cranes
1926.1400(b)Attachments are covered, including hooks, magnets, grapples and personnel platforms
1926.1400(c)(13)Excluded: tree trimming and tree removal work
1926.1400(c)(17)Excluded: certain material delivery by articulating or knuckle-boom truck cranes, with conditions
1926.1441Provisions for equipment with a rated capacity of 2,000 pounds or less

Scope: paragraphs (a) and (b)

Paragraph (a) applies the standard to power-operated equipment, when used in construction, that can hoist, lower and horizontally move a suspended load. The list of equipment names articulating cranes, such as knuckle-boom cranes, and mobile cranes including commercial truck-mounted and boom truck cranes. It also names multi-purpose machines configured to hoist and lower a load by winch or hook, service or mechanic trucks with a hoisting device, sideboom cranes, derricks and variations of this equipment.

Paragraph (b) extends the standard to those machines when used with attachments, crane-attached or suspended. The listed attachments include hooks, magnets, grapples, clamshell buckets, orange peel buckets, concrete buckets, augers or drills, pile driving equipment and personnel platforms.

Exclusions in paragraph (c)

Paragraph (c) lists what Subpart CC does not cover. Item (13) is tree trimming and tree removal work. Other items that reach the same machines are these:

  • (c)(1): machinery converted or adapted for a non-hoisting use, such as power shovels, excavators and concrete pumps
  • (c)(2): power shovels, excavators, wheel loaders, backhoes, loader backhoes and track loaders, including when used with chains, slings or other rigging to lift suspended loads
  • (c)(4): digger derricks used for augering holes for poles carrying electric or telecommunication lines, placing and removing the poles, and handling associated materials, or for other work under Subpart V
  • (c)(5): machinery originally designed as vehicle-mounted aerial devices for lifting personnel, and self-propelled elevating work platforms
  • (c)(9): a mechanic's truck with a hoisting device, when used in equipment maintenance and repair

Item (c)(17) is the material delivery exclusion. It covers articulating or knuckle-boom truck cranes that deliver material to a construction site, in two cases. One is transferring material from the truck crane to the ground without arranging it in a particular sequence for hoisting. The other is transferring building supply sheet goods or packaged materials onto a structure with a fork or cradle at the end of the boom, and only if the truck crane has a properly functioning automatic overload prevention device. The exclusion does not apply when the crane holds, supports or stabilizes material for a construction activity. It does not apply to prefabricated components such as precast concrete members, roof trusses or wall panels, or to structural steel members.

Paragraph (f) covers the actions the standard directs an operator, crewmember or other employee to take. For those, the employer must establish, communicate and enforce work rules for compliance. The scope section was last amended on November 16, 2020 (85 FR 57122), after earlier changes in 2010, 2013 and 2014.

Equipment of 2,000 pounds or less: section 1926.1441

Section 1926.1441, published at 75 FR 48172 on August 9, 2010, sets requirements for employers using equipment with a maximum rated hoisting or lifting capacity of 2,000 pounds or less. Paragraph (a) lists the Subpart CC sections that apply. They include scope and definitions, ground conditions, assembly and disassembly, power line safety, wire rope, authority to stop operation, signals, fall protection, keeping clear of the load, and equipment modifications.

Under paragraph (c), the employer follows manufacturer procedures for operation, including use with attachments, and keeps the load chart available to the operator at the control station. An anti two-block rule in paragraph (d)(2) applies for equipment manufactured more than one year after November 8, 2010. The employer must train each operator before operation under paragraph (e), and each signal person under paragraph (f). Paragraph (h) requires inspection under manufacturer procedures. Paragraph (j) bars use of this equipment to hoist personnel, and paragraph (k) requires the equipment to be designed by a qualified engineer.

OSHA's tree care rulemaking

OSHA's Tree Care Industry page says tree care hazards are addressed in specific OSHA standards for recordkeeping and general industry. The Tree Care Operations rulemaking page describes a rule that would be a new standard in 29 CFR Part 1910. It names woodchippers, stump grinders, chain saws, cranes and mobile bucket trucks among the equipment involved, and says a rule would address fall protection, falling object protection, traffic control and the safe use of tools and equipment.

OSHA lists three steps so far: an advance notice of proposed rulemaking on September 15, 2008, a stakeholder meeting on July 13, 2016, and Small Business Advocacy Review panel teleconferences in April and May 2020. Publication of a proposed rule is named as the next step. The listed references are the Fall 2022 Unified Regulatory Agenda and docket OSHA-2008-0012.

Sources