Ascender types: how the codes, EN 567 and EN 12841 type B define an ascender
Three arboriculture codes define an ascender by what it does on a rope. EN 567 covers rope clamps and EN 12841 type B covers ascending devices. None sorts ascenders into hand, chest, foot or knee types.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page draws on the named codes and training bodies. It is not training and does not teach the work.
Definitions in the codes
Each code has its own glossary entry for the word. The three wordings agree on the function: the device slides up the rope and grips when pulled the other way.
| Document | Definition |
|---|---|
| SafeWork NSW, Tree works code of practice, March 2026 | A knot or mechanical device used for ascending a rope and positioning the climber in the tree |
| Arboricultural Association, Industry Code of Practice, Edition 2, May 2020 | A mechanical device used for ascending a rope, which slides when advanced up a rope but grips when loaded in the opposite direction |
| WorkSafe New Zealand, arboriculture approved code of practice, November 2012 | A mechanical device that will slide upwards on a rope but will grip when pulled in the opposite direction |
The ICoP also has a clause on ascending devices, 3.10.6.3. It describes them as components that connect to the rope, let the rope travel through during ascent, and lock off when loaded to prevent unintentional descent.
The standards that name the device
BSI lists BS EN 567:2013, Mountaineering equipment. Rope clamps. Safety requirements and test methods, as published on 30 April 2013 and current. The scope applies to rope clamps used with dynamic mountaineering ropes to EN 892 or accessory cord to EN 564, and with low stretch kernmantel ropes to EN 1891.
A maker's technical notice for one ascender states two approvals in its field of application. The first is an ascender for mountaineering and climbing under EN 567:2013. The second is an ascending device for the work rope under EN 12841:2024 type B. Type B (ascender) and type C (descender) devices are designed for progression on a work rope, the notice states. They should be used with a fall-arrest system (type A), unless an analysis has shown that another configuration is preferable.
| Standard | Where the ascender appears |
|---|---|
| EN 567:2013 | Rope clamps, scope in the BSI catalogue |
| EN 12841:2024 type B | Ascending device for the work rope, as the maker's notice labels it |
Rules the codes attach to ascenders
SafeWork NSW lists points for choosing, using and maintaining ascenders, descenders and rope grabs in section 4.6. They should suit the rope specifications in the system, with attention to the recommended rope diameter. They should be self-locking or used with another device that is self-locking. A backup on the main climbing line should be considered in case a mechanical ascender fails.
The ICoP requires ascending devices to be compatible with the ropes used in diameter and type, ease adjustment when moving up and down the working or backup line, and give effective grip on the lines used.
The New Zealand Arboricultural Association's guide to safety requirements has rules for single rope technique access. The access line must be of double braid or kernmantel construction when toothed ascenders are used. A cam ascender should only be used in pairs or with a back up. The gap between the first and second ascender shall not be more than 500 mm.
Hand, chest, foot and knee ascenders
None of the codes or catalogue entries above sorts ascenders by body position. The words hand, chest, foot and knee ascender do not appear in them. Knee ascenders have their own guide on standards and codes. The guide to climbing devices by type covers the other devices.
Sources
- SafeWork NSW, Tree works code of practice, March 2026, section 4.6 and glossary, read October 16, 2026
- BSI Knowledge, BS EN 567:2013 Rope clamps, read October 16, 2026
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, read October 16, 2026
- WorkSafe New Zealand, Approved code of practice for safety and health in arboriculture, November 2012, read October 16, 2026
- Petzl, technical notice B0004700G (170625) for a rope clamp, read October 16, 2026
- New Zealand Arboricultural Association, Best practice guide: safety requirements for NZ arboricultural operations, Edition 3.1, 2022, read October 16, 2026