ArbNation Join free

Brush cutters and grass trimmers: ISO 11806 scope, test codes and OSHA's brush saw rule

ISO 11806 covers hand-held brush-cutters and grass-trimmers with an engine, in two parts, and both 2011 editions were withdrawn in April 2022. OSHA 1910.269(r)(6) keeps everyone but the operator 3.05 m from a brush saw's cutting head.

Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The standards are described from the catalogue entries of the Estonian standards body (EVS), which print each scope and edition history. The operator rule is 29 CFR 1910.269 in the Code of Federal Regulations.

The two parts of ISO 11806

ISO 11806 gives safety requirements and ways to verify them for the design and construction of portable, hand-held, powered brush-cutters and grass-trimmers. It covers methods for removing or reducing hazards and the information on safe working practices that the manufacturer provides. It applies to machines made after its publication date.

ISO 11806 as listed by EVS
PartMachines coveredStatus of the 2011 edition
11806-1Machines with an integral combustion engine as the power unit and mechanical power transmission to the cutting attachmentWithdrawn from April 18, 2022; the EVS history lists EVS-EN ISO 11806-1:2022 as its successor
11806-2Machines with a back-pack-mounted combustion engine and mechanical power transmission to the cutting attachmentWithdrawn from April 1, 2022; the EVS history lists EVS-EN ISO 11806-2:2022 as its successor

The EVS history for part 1 also lists an earlier edition, EVS-EN ISO 11806:2008, dated January 9, 2009. Both 2011 editions are dated January 4, 2012 in the EVS history.

Part 1 does not apply to machines with metallic cutting attachments made of more than one piece, such as pivoting chains or flail blades. Part 2 repeats that exclusion and is read together with the relevant clauses of part 1.

Part 2 leaves out one hazard. It deals with all significant hazards except whole-body vibration from the back-pack power unit. Its note says a standardized test procedure for measuring that vibration was not available.

Noise and vibration test codes

Two further ISO documents cover brush-cutters alongside saws. Both name chain-saws, brush-cutters, grass-trimmers, edgers and pole-mounted powered pruners, and both are listed against the Machinery Directive 2006/42/EC.

Test codes that name brush-cutters
StandardWhat it determinesEditions listed by EVS
ISO 22868:2021Noise emission: the A-weighted emission sound pressure level at the operator position and the A-weighted sound power level (engineering method, grade 2 accuracy)2011, dated April 5, 2011; 2021, valid from April 15, 2021
ISO 22867:2021Vibration at the handles under standardized conditions2011, dated January 4, 2012; 2021, valid from December 31, 2021

The Health and Safety Executive prints separate typical vibration levels for the two head types. A brushcutter with a saw head is given 3 to 5 m/s2, with 5 recommended as the initial value. A strimmer head is given 2 to 7 m/s2, with 7 as the initial value.

OSHA rules for backpack power units

Paragraph (r) of 29 CFR 1910.269 sets additional requirements for line-clearance tree trimming. The standard defines that as work within 3.05 m (10 ft) of electric supply lines and equipment at 50 kilovolts or less to ground, with a larger distance above 50 kilovolts. Subparagraph (r)(6) covers backpack power units for pruning and clearing.

  • While a backpack power unit is running, no one other than the operator may be within 3.05 m (10 ft) of the cutting head of a brush saw.
  • A backpack power unit must be equipped with a quick shutoff switch readily accessible to the operator.
  • Backpack power unit engines must be stopped for all cleaning, refuelling, adjustments and repairs to the saw or motor, except as the manufacturer's servicing procedures require otherwise.

Sources