ArbNation Join free

Buying a used wood chipper: what four regulators say about guards and paperwork

HSE says a used machine should reach the buyer with its guards and safety devices present and working, plus its manual. SafeWork NSW and OSHA describe the chipper guards, and WorkSafe NZ lists what a buyer checks.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. Climbing and rigging gear bought second-hand brings other questions on used gear.

Great Britain: HSE on second-hand supply

HSE's rule for second-hand work equipment is that whoever supplies it, for payment or not, must make it safe and without risks to health so far as reasonably practicable. One-off sales by users are covered, and "sold as seen" cannot be used to avoid the duty. For equipment first placed on the market under product legislation, HSE wants it supplied in the same safety condition as when first sold. That does not mean perfect condition: all health and safety features are present and working, such as guards and other safety devices in good order.

The seller supplies the original instruction manual or a copy. A machine not yet placed on the UK market, such as a grey import, falls to whoever first places it there: the importer or even the user. That person checks and if needed modifies the design, compiles a technical file, produces a Declaration of Conformity and applies conformity marking. HSE notes that grey imports are often built differently in ways not obvious on inspection, including their control and safety systems.

Great Britain: the infeed chute

HSE's information sheet AIS38(rev1), Power-fed mobile wood chippers: operator protection at infeed chutes, is written for arboriculture and forestry. It outlines the protection needed at the infeed chute, describes the types of guarding and protection devices with their design, position and function, and covers training on feeding chippers.

Australia: SafeWork NSW on guards

SafeWork NSW's Woodchipper guide lists the hazards of a trailer-mounted hand-fed chipper. They are being drawn in by the infeed rollers, contact with the blades, entanglement in branches or attached ropes, ejected material, kicking wood, crush injuries, noise, and traffic when the machine is parked on the road. The guide calls the rotating infeed rollers and the cutting disc or drum the most hazardous components. Reaching past the safety curtain or control bar can cause fatal or serious injuries.

Access to the disc and rollers from the side or top can be prevented by a fixed or interlocked guard or cover. The guide quotes the Work Health and Safety Regulation 2025, regulation 208 on guarding: a permanently fixed barrier, an interlocked barrier, a barrier removable only with tools, or a presence-sensing safeguarding system where the first three are not reasonably practicable. For bolted covers it describes a mechanical interlock: removing the bolts takes longer than the disc or drum needs to stop. An un-clutched disc or drum chipper can take up to five minutes to run down.

United States: devices OSHA names

OSHA's Safety and Health Information Bulletin 04-16-2008 is advisory and creates no legal obligations. It lists safety devices some chippers carry. Retrofit is mentioned for some of them.

DeviceRetrofit, as OSHA reports it
Feed control bar with quick-stop and reverseNot stated. OSHA reports ANSI Z133.1-2006 requiring these emergency devices on chippers with a mechanical feed control bar
Bottom feed stop barThe one manufacturer fitting it says it cannot be retrofitted to older models
Emergency pull ropesCan be retrofitted to existing machines
Feed tray extensionRetrofit kits are available
Chipper hood safety latchNot stated. It blocks starting until the hood is latched and opening before the disc or drum stops

New Zealand: Safe use of machinery, section 11

WorkSafe New Zealand's guide exempts second-hand plant sold "as is" from supplier duties, yet a business buyer still has a duty to keep it from creating risks for workers. The guide lists history and previous use, whether the machine is at the end of its life, specifications and maintenance information, the place of use, the guarding and a check by a certified engineer. For imports, it names AS/NZS 4024 as the benchmark, and says a CE mark does not by itself show a machine meets New Zealand law.

Sources