Chain markings: the codes on drive links and cutters that identify type and gauge
Saw chain carries its code on the drive links or the cutters. Oregon prints a number-and-letter key, STIHL prints an embossed pitch table, and Husqvarna lists pitch and gauge by chain type in its manual.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
Three maker manuals explain the marks on a saw chain: Oregon's chain maintenance manual, a STIHL instruction manual for a chain saw, and a Husqvarna operator's manual. Each maker uses its own key, so a code from one maker does not decode another maker's chain.
Pitch and gauge, defined
Oregon defines chain pitch as the distance between any three consecutive rivets, divided by two. Its chain gauge is the thickness of the drive link where it fits the guide-bar groove. The industry gauges Oregon lists are .043, .050, .058 and .063 inch, and it uses .063, .080 and .122 inch for harvester chain. Pitches in its range are 1/4, .325, 3/8, .404 and 3/4 inch.
Husqvarna describes the same two measures in its list of guide bar and chain data. Chain pitch is the distance between drive links, which has to match the teeth of the bar tip sprocket and the drive sprocket. The groove width in the guide bar has to equal the width of the drive links. STIHL says the drive link gauge of the chain has to match the bar groove width, and it prints drive link gauges of 1.3 mm and 1.6 mm for its .325 inch chains.
Oregon: the number stamped on the drive links
Oregon names nearly every chain by a number plus letters, as in 27A, 72LP, 91VG and M72LP. The number is stamped on the drive links and gives the physical size of the chain, pitch and gauge.
| Number | Pitch | Gauge |
|---|---|---|
| 11 | 3/4 in | .122 in |
| 16 | .404 in | .063 in |
| 18 | .404 in | .080 in |
| 20 | .325 in | .050 in |
| 21 | .325 in | .058 in |
| 22 | .325 in | .063 in |
| 25 | 1/4 in | .050 in |
| 27 | .404 in | .063 in |
| 33 | .325 in | .050 in |
| 34 | .325 in | .058 in |
| 35 | .325 in | .063 in |
| 50 | .404 in | .050 in |
| 51 | .404 in | .058 in |
| 52 | .404 in | .063 in |
| 58 | .404 in | .058 in |
| 59 | .404 in | .063 in |
| 72 | 3/8 in | .050 in |
| 73 | 3/8 in | .058 in |
| 75 | 3/8 in | .063 in |
| 90 | 3/8 in low profile | .043 in |
| 91 | 3/8 in low profile | .050 in |
| 95 | .325 in | .050 in |
Oregon: the letters
The letters give the cutter type and sequence, any kickback-reducing features, or other traits.
| Letters | Meaning in the manual |
|---|---|
| A | Micro Chisel cutters, skip sequence (27A only) |
| AK | Square-ground chisel cutters, semi-skip sequence |
| AL | Square-ground chisel cutters, standard sequence |
| AP | 25AP: Micro Chisel cutters, bumper drive links, standard sequence. 72AP: semi-chisel cutters, skip sequence |
| CL | Square-ground chisel cutters, ramped depth gauges, standard sequence |
| DP | Semi-chisel cutters, bumper drive links, standard sequence |
| H | Modified for harvester applications, Micro Chisel cutters, standard sequence |
| LP | Low-vibration round-ground chisel cutters, bumper drive links, standard sequence |
| LX | Power Sharp chain, for saws with automatic sharpening; no hand maintenance required |
| M (prefix) | Specially built chain, round-ground chisel cutters and bumper drive links, for extremely dirty or abrasive conditions |
| R, RA, RD | Ripping chain (R and RA with Micro Chisel cutters, RD with semi-chisel cutters) |
| VG | Low-vibration semi-chisel cutters, ramped depth gauges, bumper tie straps, standard sequence |
In its parts diagram Oregon names three kickback-reducing parts: bumper tie straps, bumper drive links and ramped depth gauges.
STIHL: the pitch mark on the depth gauge area
The STIHL manual says the chain pitch marking is embossed in the area of the depth gauge of each cutter. The mark is a digit or a letter, and the manual prints the pitch for each.
| Marking | Pitch | mm |
|---|---|---|
| 7 | 1/4 P | 6.35 |
| 1 or 1/4 | 1/4 | 6.35 |
| 6, P or PM | 3/8 P | 9.32 |
| 2 or 325 | 0.325 | 8.25 |
| 3 or 3/8 | 3/8 | 9.32 |
| 4 or 404 | 0.404 | 10.26 |
The same manual gives two reading rules for the type name. Micro stands for a semi-chisel tooth (examples 63 PM3, 26 RM3, 36 RM) and Super for a full chisel tooth (63 PS3, 26 RS, 36 RS3). Ripping chains carry an X in the designation, as in 63 PMX and 36 RMX. Chains with a humped drive link carry a service mark on the upper part of that link.
Husqvarna: chain type, pitch and gauge
The Husqvarna manual for the 545 Mark II and 550XP Mark II lists approved chains with their pitch, gauge in inches and millimetres, and a low kickback column. It lists chain type SP33G at 0.325 inch pitch and 0.050 in (1.3 mm) gauge, marked low kickback. Type C35 is 0.325 inch pitch and 0.058 in (1.5 mm) gauge, and is not marked low kickback. The manual does not print a decoding key for the chain type letters. It refers readers who cannot identify their chain to the maker's website.
More figures are in the guides to pitch, gauge and file size by maker and cutter types and sequences.
Sources
- Oregon Cutting Systems, Saw Chain maintenance manual (chain terms, chain identification, drive-link number and letter ID), read October 16, 2026
- STIHL, instruction manual for the MS 261 chain saw (pitch marking table, ripping chain and tooth designations), read October 16, 2026
- Husqvarna, operator's manual for the 545 Mark II, 545G Mark II, 550XP Mark II and 550XP G Mark II, dated November 19, 2024, read October 16, 2026