ArbNation Join free

Chain markings: the codes on drive links and cutters that identify type and gauge

Saw chain carries its code on the drive links or the cutters. Oregon prints a number-and-letter key, STIHL prints an embossed pitch table, and Husqvarna lists pitch and gauge by chain type in its manual.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

Three maker manuals explain the marks on a saw chain: Oregon's chain maintenance manual, a STIHL instruction manual for a chain saw, and a Husqvarna operator's manual. Each maker uses its own key, so a code from one maker does not decode another maker's chain.

Pitch and gauge, defined

Oregon defines chain pitch as the distance between any three consecutive rivets, divided by two. Its chain gauge is the thickness of the drive link where it fits the guide-bar groove. The industry gauges Oregon lists are .043, .050, .058 and .063 inch, and it uses .063, .080 and .122 inch for harvester chain. Pitches in its range are 1/4, .325, 3/8, .404 and 3/4 inch.

Husqvarna describes the same two measures in its list of guide bar and chain data. Chain pitch is the distance between drive links, which has to match the teeth of the bar tip sprocket and the drive sprocket. The groove width in the guide bar has to equal the width of the drive links. STIHL says the drive link gauge of the chain has to match the bar groove width, and it prints drive link gauges of 1.3 mm and 1.6 mm for its .325 inch chains.

Oregon: the number stamped on the drive links

Oregon names nearly every chain by a number plus letters, as in 27A, 72LP, 91VG and M72LP. The number is stamped on the drive links and gives the physical size of the chain, pitch and gauge.

Oregon chain numbers as printed in its manual
NumberPitchGauge
113/4 in.122 in
16.404 in.063 in
18.404 in.080 in
20.325 in.050 in
21.325 in.058 in
22.325 in.063 in
251/4 in.050 in
27.404 in.063 in
33.325 in.050 in
34.325 in.058 in
35.325 in.063 in
50.404 in.050 in
51.404 in.058 in
52.404 in.063 in
58.404 in.058 in
59.404 in.063 in
723/8 in.050 in
733/8 in.058 in
753/8 in.063 in
903/8 in low profile.043 in
913/8 in low profile.050 in
95.325 in.050 in

Oregon: the letters

The letters give the cutter type and sequence, any kickback-reducing features, or other traits.

Oregon chain letters, shortened from the manual
LettersMeaning in the manual
AMicro Chisel cutters, skip sequence (27A only)
AKSquare-ground chisel cutters, semi-skip sequence
ALSquare-ground chisel cutters, standard sequence
AP25AP: Micro Chisel cutters, bumper drive links, standard sequence. 72AP: semi-chisel cutters, skip sequence
CLSquare-ground chisel cutters, ramped depth gauges, standard sequence
DPSemi-chisel cutters, bumper drive links, standard sequence
HModified for harvester applications, Micro Chisel cutters, standard sequence
LPLow-vibration round-ground chisel cutters, bumper drive links, standard sequence
LXPower Sharp chain, for saws with automatic sharpening; no hand maintenance required
M (prefix)Specially built chain, round-ground chisel cutters and bumper drive links, for extremely dirty or abrasive conditions
R, RA, RDRipping chain (R and RA with Micro Chisel cutters, RD with semi-chisel cutters)
VGLow-vibration semi-chisel cutters, ramped depth gauges, bumper tie straps, standard sequence

In its parts diagram Oregon names three kickback-reducing parts: bumper tie straps, bumper drive links and ramped depth gauges.

STIHL: the pitch mark on the depth gauge area

The STIHL manual says the chain pitch marking is embossed in the area of the depth gauge of each cutter. The mark is a digit or a letter, and the manual prints the pitch for each.

STIHL pitch markings as printed in its manual
MarkingPitchmm
71/4 P6.35
1 or 1/41/46.35
6, P or PM3/8 P9.32
2 or 3250.3258.25
3 or 3/83/89.32
4 or 4040.40410.26

The same manual gives two reading rules for the type name. Micro stands for a semi-chisel tooth (examples 63 PM3, 26 RM3, 36 RM) and Super for a full chisel tooth (63 PS3, 26 RS, 36 RS3). Ripping chains carry an X in the designation, as in 63 PMX and 36 RMX. Chains with a humped drive link carry a service mark on the upper part of that link.

Husqvarna: chain type, pitch and gauge

The Husqvarna manual for the 545 Mark II and 550XP Mark II lists approved chains with their pitch, gauge in inches and millimetres, and a low kickback column. It lists chain type SP33G at 0.325 inch pitch and 0.050 in (1.3 mm) gauge, marked low kickback. Type C35 is 0.325 inch pitch and 0.058 in (1.5 mm) gauge, and is not marked low kickback. The manual does not print a decoding key for the chain type letters. It refers readers who cannot identify their chain to the maker's website.

More figures are in the guides to pitch, gauge and file size by maker and cutter types and sequences.

Sources