Chainsaw carving: kickback and protective equipment wording from CCOHS, HSE and the HSA
CCOHS, HSE and the HSA do not name carving on their chainsaw pages. Their general wording covers the kickback zone, kickback-reducing devices and the standards listed for helmets, gloves, leg protection and boots.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work.
The Canadian Centre for Occupational Health and Safety (CCOHS), the UK Health and Safety Executive (HSE) and the Irish Health and Safety Authority (HSA) each publish chainsaw safety pages. None of the three mentions carving. What they publish is general chainsaw wording, and it is reported in that form.
Kickback in the CCOHS fact sheet
CCOHS calls kickback the unexpected upward motion of the guide bar. It occurs when the end portion of the bar nose, the kickback zone, strikes an object and the chain momentarily snags or is pinched. The fact sheet quotes the CSA Z62.3-11 (R2021) definition, which has two forms. Rotational kickback is the rapid upward motion of the bar when the chain near the nose, on the top of the bar, contacts an object such as a log or branch. Pinch kickback is the backward motion when wood closes in and pinches the chain in the cut.
The most common and probably most violent kickback happens in the kickback zone. There the bar tip may move upward and back toward the operator, who could suffer a very serious or fatal injury.
The sheet gives a chain brake, low kickback chain and reduced kickback chain as examples of kickback-reducing devices. It ties them to standards such as CSA Z62.3-11 (R2021) and ANSI B175.1-2021, and states that these devices reduce kickback but do not prevent it. It also describes a safety tip that covers the nose of the bar, and says the tip must be removed for bore cuts (pocket cuts) or for wood thicker than the bar is long. Its list of things to avoid includes cutting in the kickback zone and sawing above shoulder height.
Protective equipment in the HSE guidance
The HSE chainsaw PPE page lists a standard for each item, separately for a chainsaw used on the ground and one used off the ground. The standards are the same for both except for the helmet.
| Item | Standard listed | Other wording on the page |
|---|---|---|
| Safety helmet, on the ground | BS EN 397, BS EN 14052 or BS EN 12492 | Helmets to BS EN 397 or BS EN 14052 are only recommended for ground work |
| Safety helmet, off the ground | BS EN 12492 | A mountaineering style helmet |
| Hearing protection | BS EN 352-1, BS EN 352-2 or BS EN 352-3 | Same on and off the ground |
| Mesh visor | BS EN 1731 | Eye and face protection from flying debris and branches |
| Safety glasses or goggles | BS EN 166 | Glasses may stay on the head less well than goggles for work at height |
| Gloves | BS EN 381-7 | Where chainsaw protection is required |
| Leg and groin protection | BS EN 381-5 | The page cites AFAG on Type C for aerial work, and Type A where risk assessment justifies it |
| Chainsaw boots | BS EN ISO 17249 | Good grip and guarding at the front vamp and instep |
| Gaiters | BS EN 381-9 | For occasional users on even ground, worn with steel toe-capped safety boots |
| Outer clothing | None listed | Should be non-snag |
| High visibility clothing | None listed | Where justified by risk assessment |
People who are not using the chainsaw may also need head, hearing or eye protection, as identified in the task risk assessment.
The HSA leaflet on competence
The HSA leaflet "Are you competent to operate a chainsaw safely?" sets out a written risk assessment before work starts, listing the hazards and the control measures. It describes an accredited chainsaw training course with an assessment suited to the work. A basic course covering the felling of small trees is up to 5 days long, and the leaflet says short courses on maintenance and cross cutting do not demonstrate felling techniques.
The leaflet's equipment list gives a helmet to EN 397, a visor to EN 1731 or safety glasses to EN 166, and ear defenders to EN 352. It lists chainsaw gloves with a protective pad on the back of the left hand and leg protection incorporating clogging material, both under EN 381-7. Chainsaw trousers are listed under EN 381-5, and safety boots with steel toecaps under EN 381/345. Outer clothing is close-fitting and non-snag.
The leaflet states that no personal protective equipment gives 100 percent protection against cuts from a hand-held chainsaw, and that it does not protect against falling trees. It also says a first aid kit, including a large wound dressing, should be readily available.
The HSE and HSA lists differ on glove and leg standards. HSE gives EN 381-7 for gloves and EN 381-5 for leg protection. The HSA ties EN 381-7 to both the gloves and the clogging-material leg protection, then lists the trousers under EN 381-5.
Gaps in the sources
None of the three pages describes carving work, carving saws or carving events. They give no figure for injuries in carving and no rule that applies only to it.
Sources
- CCOHS, Chainsaws: Kickback, OSH Answers, fact sheet last revised August 22, 2023, read October 19, 2026
- UK Health and Safety Executive, Chainsaw personal protective equipment (PPE), page dated September 18, 2026, read October 19, 2026
- Health and Safety Authority (Ireland), Are you competent to operate a chainsaw safely? (undated leaflet), read October 19, 2026