Chainsaw jackets and upper-body protection: EN 381-11, EN ISO 11393-6 and HSE guidance
HSE's chainsaw leaflet names chainsaw jackets to BS EN 381-11 as extra protection for people at increased risk. That standard was withdrawn from August 1, 2019, in the EVS listing, and replaced by EN ISO 11393-6.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The named codes and standards bodies are described here as published. It is not training and does not teach the work.
HSE leaflet INDG317
HSE's leaflet Chainsaws at work, INDG317 (revision 2, January 2013), lists upper body protection as chainsaw jackets to BS EN 381-11. The leaflet says jackets can provide additional protection where operators are at increased risk. Its examples are trainees and unavoidable use of a chainsaw above chest height. It adds that this needs to be weighed against the greater heat stress from physical exertion, such as working from a rope and harness.
The leaflet says no protective equipment can give 100 percent protection against cutting by a hand-held chainsaw. In its kickback section it says kickback is responsible for a significant proportion of chainsaw injuries, many of them to the face and parts of the upper body where it is difficult to provide protection. A maintained chain brake and low-kickback chains reduce the effect but cannot entirely prevent it.
The same PPE list in the leaflet names the other items with their standards: a safety helmet to EN 397, hearing protection to EN 352-1, and a mesh visor to EN 1731 or safety glasses to EN 166. Gloves are to EN 381-7 where chainsaw gloves are required, and leg protection is to EN 381-5. It says all-round leg protection is recommended for arborists working in trees.
HSE's chainsaw PPE page
HSE's separate chainsaw PPE page for tree work has rows for helmets, hearing protection, eye protection, gloves, leg and groin protection, chainsaw boots, gaiters, outer clothing and high visibility clothing. It has no row for jackets. For outer clothing it says only that it should be non-snag. For leg protection it reports that AFAG recommends Type C leg protection for aerial work because of the high all-round cut protection. Where Type C is impractical, such as because of the higher risk of heat stress, Type A may be appropriate where a risk assessment justifies it.
The standard: EN 381-11 and its replacement
The standards catalogues of EVS in Estonia and the Swedish Institute for Standards (SIS) both list EN 381-11, Protective clothing for users of hand-held chainsaws, Part 11: Requirements for upper body protectors. Its scope covers the protection upper body protectors give against cutting by a hand-held chainsaw, assessed by the test methods in EN 381-10. It also covers ergonomic properties, identification, marking and the information the maker supplies, including selection criteria and instructions for use.
| Item | Record |
|---|---|
| Standard | EN 381-11, adopted in Estonia as EVS-EN 381-11:2003 and in Sweden as SS-EN 381-11 |
| Subject | Requirements for upper body protectors for users of hand-held chainsaws |
| Status | Withdrawn. EVS gives August 1, 2019. |
| Replaced by | EN ISO 11393-6:2019 (EVS-EN ISO 11393-6:2019, SS-EN ISO 11393-6:2019) |
| Approved (SIS) | December 20, 2002 |
HSE's 2013 leaflet therefore names a standard that the two catalogues list as withdrawn. The catalogue entries give the replacement but not its scope. The guide to chainsaw clothing labels covers the markings, and chainsaw operator PPE rules by country covers the rules.
Sources
- HSE, Chainsaws at work, INDG317 (rev2), January 2013, read October 21, 2026
- HSE, Chainsaw personal protective equipment (PPE), tree work, read October 21, 2026
- Eesti Standardimis- ja Akrediteerimiskeskus, EVS-EN 381-11:2003 catalogue entry, read October 21, 2026
- Swedish Institute for Standards SIS, SS-EN 381-11 catalogue entry, read October 21, 2026