ArbNation Join free

Chainsaw leg protection: EN 381-5, ISO 11393-2 and the types regulators name

HSE points to EN 381-5 for chainsaw leg protection and names Type A and Type C. WorkSafeBC accepts ISO 11393-2, EN 381-5, ASTM F1414-04 or its own standard, and names pant, apron and chap types.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. HSE and WorkSafeBC name leg protection standards for chainsaw users, and each uses its own words for the designs.

The two standards

Leg protector standards named by the sources
StandardScope or status as published
BS EN 381-5:1995Protective clothing for users of hand-held chain saws, Part 5: requirements for leg protectors. WorkSafeBC lists it by this title. HSE still cites BS EN 381-5 for leg and groin protection
ISO 11393-2:2018Protective clothing for users of hand-held chainsaws, Part 2: performance requirements and test methods for leg protectors. Published October 1, 2018. The scope covers performance requirements, test methods, design requirements, identification and marking for leg protectors against cutting by hand-held chainsaws. The ISME listing gives current stage 90.93 with an effective date of May 28, 2026, and shows ISO 11393-2:1999 as previously withdrawn
EN ISO 11393-2:2019The European adoption of the ISO text, valid from October 15, 2019 in the Estonian standards catalogue. The catalogue history also lists EN 381-5:1999 and EN 381-2:1999. The entry is tied to Regulation 2016/425 on personal protective equipment

Leg protection in HSE guidance

The HSE leaflet Chainsaws at work (INDG317, published 01/13) shows leg protection to EN 381-5 in its PPE figure. It adds that all-round protection is recommended for arborists working in trees and for occasional users such as those working in agriculture.

The HSE page on chainsaw PPE lists BS EN 381-5 for leg and groin protection both on the ground and off the ground. AFAG, which HSE cites, recommends Type C leg protection for aerial work, because of its high all-round chainsaw cut protection. Where Type C is impractical, for example because of the higher risk of heat stress, HSE says Type A may be appropriate where a risk assessment justifies it. The HSE page on PPE for aerial tree work repeats this and says AFAG strongly recommends Type C.

Leg protection in British Columbia

Section 8.21 of the British Columbia OHS Regulation says leg protective devices must be worn by a worker operating a chain saw. The device has to meet the general requirements in Schedule 8-A and the performance requirements of one of four standards. The regulation sets the threshold chain speed for each.

Performance standards accepted by OHS Regulation 8.21(2)(b)
StandardThreshold chain speed
WorkSafeBC Standard, Leg Protective Devices (Schedule 8-A, section 5)18.3 m/s (3,600 ft/min)
ASTM F1414-04 cut resistance test method16.8 m/s (3,300 ft/min)
ISO 11393-2Class 2, 24 m/s (4,724 ft/min)
BS EN 381-5:1995Class 2, 24 m/s (4,724 ft/min)

Schedule 8-A names three types of leg protection. A pant type has the protective pad secured to and held in place by the trousers. An apron type has the pad on an apron-style garment worn outside the trousers and secured around the legs and waist. A chap type has the pad on a chap-style garment worn outside the trousers and secured around the legs.

The schedule sets the pad at least 711 mm (28 in) long, covering 180 degrees at the front of both legs from inseam to outseam plus 100 mm (4 in) on the left side of both legs. In its own threshold test the pad has to resist a running chain at 1,098 m/min (3,600 ft/min) or more for at least 1.01 seconds. The label has to be permanent, with letters at least 6 mm high, and has to show the maker, the Schedule 8-A standard, the performance standard and the year of manufacture unless it is marked elsewhere. Section 8.21(4) exempts a firefighter using a chain saw at the scene of a structural fire.

Sources