Chainsaws in fire season: spark arresters, fire watch and shutdown levels, Oregon and BC
Oregon's industrial fire rules set spark arrester, fire tool and fire watch minimums for power saws, and its precaution levels limit saw hours. British Columbia lists power saw use in cutblocks as a high risk activity.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. Oregon's rules come from two Oregon Department of Forestry (ODF) sheets. British Columbia's come from the BC Wildfire Service page on high risk activities, which quotes the Wildfire Act and the Wildfire Regulation (BC Reg 38/2005). Fire and fuel hazards in tree work have their own guide.
Oregon fire season requirements
ODF's sheet on fire season requirements of industrial operations calls its contents minimum standards by law and adds that many landowners require more. It covers smoking, fire tools, fire extinguishers, spark arresters, water supply, fire watch and fire prevention in the operation area.
Smoking is barred while working in or travelling through an operation area. For fire tools, the sheet sets a box of tools equal to the number of workers when five or more are on the operation, and a shovel for each worker when there are four or fewer. Each person operating a power saw must have a shovel immediately available for fighting fire.
The extinguisher line for power saws is 8 oz or more of fire suppressant. Trucks and equipment with internal combustion engines carry a 2A:10BC (5 lb) extinguisher or equivalent with a pressure gauge.
Spark arresters on saws
The sheet requires a spark arrester on all non-turbocharged engines, with a short list of exceptions. For power saws, the line is that they must meet the spark arrester guide requirements, defined as a stock exhaust system and a screen with holes smaller than 0.023 inch.
Fire watch in Oregon
Each operation area is to have a fire watch during fire season. The fire watch is on duty during any breaks and for two hours after all power-driven machinery has shut down for the day. The sheet notes that some ODF districts waive this requirement based on the precaution level in place.
The sheet describes the fire watch as someone physically capable and experienced to operate firefighting equipment, with transport and communications to summon help, who observes all parts of the operation where work happened that day. On finding a fire, that person reports it first and summons help.
Industrial fire precaution levels west of the Cascades
ODF's industrial fire precaution level (IFPL) sheet sets four levels for operations on land it protects west of the Cascades. The system does not apply on ODF-protected land east of the Cascade summit. Fire season is the season when a fire hazard exists, as declared by the responsible agency official.
| Level | What the sheet lists for power saws |
|---|---|
| IFPL I, fire season | Fire season requirements apply. A fire watch is required at this and every higher level unless waived. |
| IFPL II, limited shutdown | Power saws, except at loading sites, may operate only between 8 P.M. and 1 P.M. |
| IFPL III, restricted shutdown | Power saws on ground-based operations may run between 8 P.M. and 1 P.M. where mechanized equipment that can build fire line is immediately available. Power saws at loading sites may run between 8 P.M. and 1 P.M. |
| IFPL IV, complete shutdown | All operations are prohibited. |
The same sheet allows written waivers, issued in advance, for power saws at loading sites or in felling and bucking where extra prevention measures cut fire risk. Its checklist for forest operations lists cleaning out spark arrester ports and monitoring relative humidity hourly, with shutdown considered when humidity drops below 30 percent.
British Columbia high risk activities
Section 6 of the Wildfire Act covers high risk activities on or within 300 m of forest land or grass land. From March 1 to before November 1, unless the area is snow covered, the person carrying out the activity must determine the Fire Danger Class for the location.
The Wildfire Regulation defines high risk activities. They include using fire- or spark-producing tools, including cutting tools. They also include operating a power saw in a cutblock, outside a road, landing, roadside work area or log sort area.
| Fire danger class | Restriction |
|---|---|
| I and II | No restrictions |
| III, moderate | After 3 consecutive days of class III or greater, a fire watch for at least one hour after the activity ends |
| IV, high | A fire watch for at least two hours after the activity ends. After 3 consecutive days of class IV, activity stops between 1 p.m. local time and sunset each day |
| V, extreme | Activity stops between 1 p.m. PDT and sunset and a fire watch of at least two hours follows. After 3 consecutive days of class V, activity stops all day |
The BC page also gives durations. A class IV fire watch runs until the rating falls to class III for two consecutive days or below class III. A class V restriction runs until the rating falls below class IV for two or more consecutive days. The regulation text quoted is the April 2023 consolidation.
Sources
- Oregon Department of Forestry, Industrial Fire Precaution Levels (IFPLs) for ODF Protection west of the Cascades, read October 16, 2026
- Oregon Department of Forestry, Fire Season Requirements of Industrial Operations, read October 16, 2026
- BC Wildfire Service, High risk activities, updated February 25, 2026, read October 16, 2026