ArbNation Join free

Chipper standards and design features: EN 13525, ANSI Z133 and what OSHA names

EN 13525:2020 sets the safety rules for manually fed wood chippers in Europe. In the United States, OSHA names the feed control bar that ANSI Z133.1 requires and lists the other devices makers have fitted.

Checked against the sources at the bottom of this page on October 18, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here.

The standards

Chipper standards named by the sources
StandardWhat the published scope or OSHA text records
EN 13525:2020, Forestry machinery, wood chippers, safetySafety requirements and their verification for the design and construction of self-propelled, mounted, semi-mounted and trailed wood chippers used in forestry, agriculture, horticulture and landscaping. Valid from May 4, 2020 in the Estonian catalogue, whose history also lists EN 13525:2005+A2:2009
ANSI Z133.1-2006, Safety Requirements for Arboricultural OperationsPer OSHA, requires chippers with a mechanical feed control bar to have quick-stop and reverse feed devices for emergencies
29 CFR 1910.212(a)(1) and (a)(3)Machine guarding for the operator and others in the work area, and guarding of the point of operation
29 CFR 1910.266(h)(4)For in-woods chipping under the logging standard, infeed and discharge ports guarded against contact with the disc, knives or blower blades; access covers or doors not opened until the drum or disc is at a complete stop

Scope of EN 13525:2020

The standard applies to chippers used when stationary and loaded by hand through a horizontal or near horizontal infeed chute. The infeed action may come from the chipping components or from rollers or conveyors built into the chute. Power can come from an external power take-off or hydraulics, or from an integral engine.

The catalogue lists what it leaves out: road regulations for travel between sites, hazards of any self-propelled function, power take-off drive shafts, engine pull starting, mechanical loading and vertical infeed chutes. It also leaves out machines whose infeed chute has an extension table or conveyor reaching past the outermost lower edge of the chute and its Lower Protective Device, and shredder-chippers covered by EN 13683. The standard does not apply to chippers made before its publication by CEN. It links to the Machinery Directive 2006/42/EC. Its noise test code does not comply with the outdoor noise directive 2000/14/EC.

Controls and devices OSHA lists

OSHA Safety and Health Information Bulletin 04-16-2008 says it is advisory and creates no new legal obligations. It records 39 chipper deaths from 1996 to 2005 in OSHA's IMIS data. Of these, 78 percent resulted from being caught in the chipper and most of the rest from being struck by it. The bulletin lists devices that some makers fit. The list below describes each as OSHA does, without naming makers.

  • Feed control bar. Mounted across the top and along the sides of the infeed chute. Pushing it to the centre stops the feed rollers, and pushing it toward the discharge spout reverses them.
  • Bottom feed stop bar. A pressure-sensitive device that cuts off all power when 34 pounds of force are applied to the lower edge of the feed table. OSHA reports the maker says it cannot be fitted to older models.
  • Panic bar. Stops the hydraulic system that drives the feed rollers when grabbed. It has two grab bars, one in front and one behind the feed control bar.
  • Emergency pull ropes. Two ropes or cables on both sides of the throat of the infeed chute that reverse the feed rollers. They can be fitted to existing machines. OSHA notes they may be hard to find in an emergency if tangled in branches.
  • Feed tray extensions. Longer or fold-down trays that can add as much as four feet to the infeed area.
  • Flexible rubber curtain or flaps. Fitted at the front of the infeed chute to warn against reaching in and to stop objects kicking back.
  • Discharge spout deflector or guard. Redirects chips into a chipper truck or away from workers.
  • Chipper hood safety latch. An interlock that stops the chipper starting before the hood is locked and stops the hood opening before the disc or drum has stopped.

OSHA 3940, Solutions for Tree Care Hazards (2018), lists chipper hazards as workers pushing material in by hand, leaning too far into the hopper, material thrown from the machine and hazardous noise. It names safety guards, controls and emergency shut-off devices among the items to confirm are working.

Sources