ArbNation Join free

Chippers by power and mounting: PTO, engine, electric, trailed, mounted, self-propelled

EN 13525 covers trailed, mounted, semi-mounted and self-propelled chippers used when stationary. EN 13683 covers hand-fed shredders and chippers with an integral power source and leaves out electric and battery machines.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. Feed types are compared in the guide to chipper types by feed and chute.

Two European standards, two scopes

BSI, the British standards body, lists BS EN 13525:2020, Forestry machinery, Wood chippers, Safety, and BS EN 13683:2003+A2:2011, Garden equipment, Integrally powered shredders/chippers, Safety. Each has its own scope.

EN 13525:2020

ItemScope
MachineWood chippers used in forestry, agriculture, horticulture and landscaping
MountingSelf-propelled, mounted, semi-mounted and trailed, used when stationary
PowerHazards from transmitting power from an external source, such as power take-off driveshafts, and from pull-starting an integral power source are left out
FeedManual loading through a horizontal or near horizontal infeed chute
Left outVertical infeed chutes, machines loaded only mechanically, hazards of the self-propelled function and of power take-off drive shafts

EN 13683:2003+A2:2011

ItemScope
MachineHand-fed shredders and chippers, with or without vacuum-assisted collection
MountingOutdoor use in a stationary position, operator standing on the ground
PowerIntegral power source only
FeedHand-fed, with feed openings that fit a 250 mm by 250 mm square
Left outUnits driven by an external power source, mobile use, powered discharge, separate powered feed, electric and battery-powered units

Power

EN 13525 leaves out the hazards from transmitting power from an external power source, with power take-off driveshafts as the example. It also leaves out the hazard of pull-starting the engine of an integral power source.

EN 13683 is narrower. Its scope is shredders and chippers with an integral power source. Units driven by an external power source are outside it, and so are electrically powered and battery-powered units.

Mounting and travel

EN 13525 names four forms: self-propelled, mounted, semi-mounted and trailed. It applies to the chipper used when stationary. Road rules for travel between work sites and the hazards of any self-propelled function fall outside the scope.

EN 13683 applies to units used outdoors in a stationary position. A unit that can run in both stationary and mobile modes is outside the scope for its mobile use.

Feed

EN 13525 covers manual loading through a horizontal or near horizontal chute. The infeed action comes from the chipping components themselves or from rollers or conveyors that are part of the chute. A machine with an extension table or conveyor protruding beyond the lower edge of the chute is outside the scope. So is a machine that is only loaded mechanically. Where a machine can be fed both ways, the standard covers the manual loading only.

EN 13683 covers hand-fed units whose feed openings, taken together, fit into a square of 250 mm by 250 mm at the plane of the opening.

Editions and regulator sheets

BSI says BS EN 13525:2020 supersedes BS EN 13525:2005+A2:2009, which is withdrawn, and adds requirements for moving parts. HSE's sheet is written around the older edition. It says new machines supplied on or after 27 June 2005 must comply with BS EN 13525:2005+A2:2009. For power-fed chippers, HSE sets out chute dimensions and infeed protection devices, with different criteria by supply date and by the height of the lower chute edge.

WorkSafe New Zealand names AS/NZS 4024.1:2014 as the minimum standard there. It gives the lower edge of the infeed chute as between 600 mm and 1000 mm from the ground, with at least 1500 mm from the infeed rollers to any part of the chute's outer edges. The sheet says a chipper modified away from its maker's standard may breach that standard and compromise safety, and that a modification should be done in consultation with the manufacturer, and/or certified by an engineer as safe.

Sources