ArbNation Join free

Climbing gloves, knee pads and rain gear: EN 388/EN 381 hand and leg standards in the climbing context

Two standards cover the hands and legs of a tree climber: EN 388 for gloves against mechanical risks and EN ISO 11393-2, which replaced EN 381-5, for chainsaw leg protectors. No source read names a standard for knee pads or rain gear.

Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The facts come from the HSE, standards catalogues and the Industry Code of Practice for Arboriculture (ICoP).

HSE list for chainsaw climbers

The Health and Safety Executive page on aerial tree work lists the protective equipment chainsaw users wear when climbing. That is a safety helmet, with AFAG recommending a mountaineering style helmet to BS EN 12492. It is also eye protection to BS EN 1731 or BS EN 166, hearing protection to BS EN 352 and protective boots to BS EN ISO 20345.

For hands, the list reads "suitable gloves appropriate to the task and subject to the operator's risk assessment". It names no glove standard. For legs, it lists leg and groin protection to BS EN 381-5. AFAG strongly recommends Type C leg protection for aerial work because of its high all-round chainsaw cut protection. Where Type C is impractical, for example because of the higher risk of heat stress, Type A may be appropriate where a risk assessment justifies it. Non-snag outer clothing is also on the list, and high-visibility clothing may be appropriate.

Gloves: EN 388

BSI lists BS EN 388:2016+A1:2018, Protective gloves against mechanical risks, published January 31, 2019, as current and under review. It replaces BS EN 388:2016, which is withdrawn. The Estonian standards body lists it as valid from January 3, 2019, under Regulation (EU) 2016/425 on personal protective equipment.

The scope is the same in both catalogues. EN 388 specifies requirements, test methods, marking and information for protective gloves against the mechanical risks of abrasion, blade cut, tear, puncture and, if applicable, impact. It is intended for use with EN 420, and its test methods may also apply to arm protectors.

Legs: EN 381-5 and EN ISO 11393-2

The sources disagree on which leg standard is current. The HSE page still names BS EN 381-5. The Estonian catalogue shows EN 381-5 as withdrawn from October 15, 2019, and lists EVS-EN ISO 11393-2:2019 as its replacement. AFNOR lists NF EN ISO 11393-2, September 2019, 37 pages, as current. It shows NF EN 381-5 (July 1995) and NF EN 381-2 as cancelled and replaced by it.

StandardScope in the catalogue entry
EN 381-5, Protective clothing for users of hand-held chain saws. Requirements for leg protectorsDefines the design of leg protectors that protect against cutting from a hand-held chain saw. Covers requirements for identification, marking and information for the user. Withdrawn from October 15, 2019.
EN ISO 11393-2, Protective clothing for users of hand-held chainsaws. Part 2: Performance requirements and test methods for leg protectorsPerformance requirements, test methods, design requirements, identification and marking information for leg protectors against cuts from hand-held chainsaws. ISO 11393-2:2018, adopted as an EN in 2019.

Knee pads and rain gear

The HSE list has no knee pads and no rain gear. The ICoP counts items worn by the user as PPE, for example helmet, gloves, boots, trousers, ear and eye protection. Its clause 3.10.8 lists the points for selecting PPE. It should suit the task, control the risks, fit the wearer, allow an unrestricted range of movement and vision, work with other PPE worn at the same time, and not expose the wearer to greater risks than the task.

Chainsaw clothing labels and classes have their own guide: chainsaw trousers, boots and gloves labels.

Sources