Cut-resistant work gloves: EN 388, ANSI/ISEA 105 and chainsaw gloves under EN 381-7
EN 388 covers abrasion, blade cut, tear, puncture and impact for protective gloves. HSE names EN 381-7 for chainsaw gloves, and OSHA 1910.138 leaves glove selection to an evaluation of the task and hazards.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here.
Standards and rules named for hand protection
| Standard or rule | What the published text records |
|---|---|
| EN 388:2016+A1:2018, Protective gloves against mechanical risks | Requirements, test methods, marking and supplier information for gloves against abrasion, blade cut, tear, puncture and, if applicable, impact. Meant to be used with EN 420. The test methods may also apply to arm protectors. Valid from January 3, 2019 in the Estonian catalogue |
| EN 381-7, chainsaw protective gloves | HSE names it for gloves on the ground and off the ground: where chainsaw protection is required, it should be to BS EN 381-7 |
| ANSI/ISEA 105-2024, American National Standard for Hand Protection Selection Criteria | Listed by the International Safety Equipment Association under hand protection |
| ANSI/ISEA 138-2019, Performance and Classification for Impact-Resistant Gloves | Listed by the International Safety Equipment Association under hand protection |
| 29 CFR 1910.138, Hand protection (OSHA) | The employer selects and requires appropriate hand protection when hands are exposed to hazards such as severe cuts or lacerations, severe abrasions and punctures. Selection rests on the performance characteristics of the glove relative to the task, conditions present, duration of use and hazards identified |
United States
OSHA's hand protection rule lists hazards: skin absorption of harmful substances, severe cuts or lacerations, severe abrasions, punctures, chemical burns, thermal burns and harmful temperature extremes. It does not name a glove standard. ISEA lists ANSI/ISEA 105-2024 as the selection-criteria standard and ANSI/ISEA 138-2019 for impact-resistant gloves.
OSHA's chipper bulletin SHIB 04-16-2008 lists gloves with no cuffs (non-gauntlet) among the clothing recommended under ANSI Z133.1-2006 for work at a chipper. In its fatality account, the operator wore leather gloves with cuffs, and OSHA says a branch may have snagged a cuff.
United Kingdom
HSE's page on chainsaw PPE lists BS EN 381-7 for gloves, for work on the ground and off the ground alike. It describes suitable gloves as subject to the operator's risk assessment, with protection to consider from cuts from the chainsaw, thorny material and cold or wet conditions. The HSE leaflet INDG317 says the same, and adds that the type of glove depends on a risk assessment of the task and machine.
EN 388 and EN 381-7 compared
The European standard names five mechanical risks. Abrasion, blade cut, tear and puncture are always in scope, and impact applies where relevant. EN 388 is a general mechanical-risk standard. EN 381-7 is the one HSE names for gloves that must resist a chainsaw.
Sources
- US OSHA, 29 CFR 1910.138 Hand protection, read October 16, 2026
- HSE, Chainsaw personal protective equipment (PPE), tree work, read October 16, 2026
- HSE, Chainsaws at work, INDG317 (published 01/13), read October 16, 2026
- International Safety Equipment Association, ISEA standards listing, read October 16, 2026
- Estonian Centre for Standardisation and Accreditation (EVS), EVS-EN 388:2016+A1:2018 catalogue page, read October 16, 2026
- US OSHA, Hazards of Wood Chippers, SHIB 04-16-2008, read October 16, 2026