ArbNation Join free

Danger trees and snags in wildland and forest work: BC and US Forest Service publications

WorkSafeBC defines a dangerous tree as any tree, of any size, that is a hazard to a worker. A BC wildfire workbook, a forest safety alert, a Ministry road procedure and two US Forest Service guides set out how such trees are rated.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page draws on British Columbia and US Forest Service publications. It is not training and does not teach the work. It is not a diagnosis of any tree and does not say what should be done with one.

The WorkSafeBC definition

The BC Wildlife/Dangerous Tree Assessor's Course workbook for wildland fire safety (revised March 2020) is co-published with WorkSafeBC. It sets out the definition from section 26.11 of the WorkSafeBC Occupational Health and Safety Regulation. A dangerous tree is any tree, whatever its size, that is a hazard to a worker because of location or lean, physical damage, overhead hazards, deterioration of limbs, stem or root system, or a combination of these.

The workbook notes that "snag" was historically defined in forestry operations as a standing dead or dying tree over 3 metres in height. It adds that live trees can have features hazardous to workers. The workbook gives the Section 26.11 interpretation of a dangerous tree as the one that applies.

Section 26.11(1), as quoted there, covers the case where it is known or reasonably foreseeable that work will expose a worker to a dangerous tree. Either the tree must be felled, or a risk assessment of the tree must be done by a person who has completed a training program acceptable to the Board. The workbook sums up risk as hazard multiplied by exposure, and counts exposure beyond the work area to the perimeter within one tree length or more, plus rest and staging areas.

The five-step process in the BC workbook

The workbook lists five steps for dangerous tree decisions: a site assessment overview, the level of disturbance of the work activity, a visual tree inspection, a safety decision of Safe or Dangerous, and documentation. Its disturbance table runs from very low risk activities such as surveys and patrolling, through low, medium and high. Tree falling and use of heavy mechanized equipment sit at medium. Fire camps and helicopter staging areas sit at high.

For low-disturbance activities, the workbook names three significant hazard indicators of imminent failure. One is an insecurely lodged tree or a hung-up limb or top. Another is a highly unstable tree, with more than 50 percent of the cross-sectional area damaged or decayed. The third is a recent lean toward the work area together with a decayed root system. All other trees are rated Safe for those activities.

The workbook's summary of assessment requirements exempts very low risk activities from a pre-work inspection. Foot patrolling in burned stands is the exception. Other activities need a pre-work inspection by a certified Dangerous Tree Assessor, or for low disturbance a Qualified Person. For a tree rated Dangerous, the listed actions are removing the tree, removing the hazardous part, flagging a no-work zone and instructing workers to stay out of it. The zone is usually 1.5 defect lengths in size in its table for low-disturbance work.

The BC Forest Safety Council alert

The Falling Technical Advisory Committee issued a Danger Tree Assessment alert on August 14, 2025 through the BC Forest Safety Council. The alert records a rise in serious injuries and fatalities in forestry, oil and gas, and wildfire work in British Columbia over 2023 to 2025. Struck-by incidents from falling trees and fire-related dangers are its named hazards. Root rot, lean, cracks and fire damage are the risks it says qualified assessors identify. A free Danger Tree Awareness course from the council is pointed to.

Ministry of Forests SOP-11 for roadside danger trees

The BC Ministry of Forests procedure SOP-11, dated January 8, 2026, covers danger tree removal along resource roads. Its stated aim is to remove only trees that present a demonstrable hazard. Dead, rotten, leaning or otherwise unstable trees that could reasonably reach the road surface must be assessed and, where necessary, felled.

The procedure lists conditions that stop work, among them an active bird nest in the work area, contact with utility infrastructure and a traffic accident or near miss. It states that hand fallers must be trained and certified under Part 26 of the WorkSafeBC regulation. Mechanical falling is not done in watercourses or riparian areas. Snags that present no safety risk are retained where feasible.

US Forest Service hazard tree guides

The Pacific Southwest Region's hazard trees page describes its Forest Health Protection program as giving guidance on hazard tree identification and assessment along National Forest system roads and in developed recreation areas. It also provides training and train-the-trainer sessions.

The Northern and Intermountain Regions' guide (R1-17-31, 2024 reprint) is written for developed recreation sites. It rates a hazard tree by adding three scores: Failure Potential from 1 to 4, Damage Potential from 1 to 3 and Target Value from 1 to 3. Ratings run from 3 to 10, and the guide treats 3 to 7 as low priority, 8 as moderate, 9 as high and 10 as severe.

That guide counts dead trees of any species, size or age as high Failure Potential. Its defect table gives examples such as a canker girdling more than half the circumference of the bole, and a height to diameter ratio above 100 at the high end. It adds that a highly defective tree can still receive a low treatment priority if Damage Potential and Target Value are minimal.

Sources