Descenders and figure-eight devices: what EN 341/UIAA 129 cover and what tree codes say
EN 341 covers descender devices for rescue and leaves out descending in mountaineering, rope access and work positioning. UIAA 129 covers braking devices. The ICoP sets five duties for descending devices. No source names a figure-eight.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The standards below are catalogue and announcement records, the Industry Code of Practice for Arboriculture: Tree Work at Height (ICoP, Edition 2, May 2020) and a maker's summary of EN 12841.
EN 341: descender devices for rescue
BSI lists BS EN 341:2011 as current and under review, published August 31, 2011. It replaces EN 341:1992, which is withdrawn. The standard specifies requirements, test methods, marking and manufacturer information for descender devices, with their descent lines, intended for rescue and for protection against falls in a rescue system.
BSI defines a descender device as an automatic (type 1) or manually operated (type 2) device, including a line. People use it to rescue themselves or others from a higher to a lower position at a limited velocity, so that a free fall is prevented. EN 341 sets no requirements for descender devices used for descending in mountaineering, rope access or work positioning systems. A descender that lets the user rescue himself and conforms to EN 341 is personal protective equipment.
UIAA 129: braking devices
The UIAA safety standards list carries UIAA 129 Braking Device and UIAA 128 Energy Absorbing Systems. A June 25, 2009 UIAA announcement covers the first braking device standard. The Safety Commission adopted the draft at its May meeting in Golden, Colorado, and the standard was to be available from September 30, 2009 and to take effect on January 1, 2011.
The standard deals with four kinds of braking device: manual, locking-assisted, abseiling devices, and abseiling devices with a panic function. It sets static strength tests for the stress on both the rope and the device. For locking-assisted devices it uses dynamic loads to see how far the rope slips in arresting a fall and whether rope or device is damaged. Makers that meet it may show the UIAA Safety Label.
Descending devices in the ICoP
ICoP clause 3.10.6.7 defines a descending device as a manually operated device for descending a rope, often with a smooth cam, a roller or another friction system to regulate the speed. Some have auto-locking and fail-to-safe functions. The clause sets five duties.
- A fall must not be possible through release of a control element or grip position.
- The device must suit the length and duration of the descent.
- It must handle two-person loading if rescue requires it.
- It must regulate the speed of descent.
- It must be compatible with rope type and diameter.
Clause 3.10.6.11 treats lowering devices separately: a tube or bollard around which the rope is wound to create friction or a deviation. They must be rated for the anticipated loads, including any dynamic loading during rigging.
The ICoP standards list in Part 6 names BS EN 341, BS EN 12841 for rope adjustment devices, EN 15151 for braking devices with manually assisted locking, and ISO 22159 for descending devices.
EN 12841 type C in a maker's summary
A rope-access equipment maker's simplified summary of EN 12841:2006 defines type C as a manually operated, friction-based rope adjustment device. It lets the user descend under control and stop at any point without holding on by hand. The summary prints these test figures for type C:
| Test | Type C figure |
|---|---|
| Static strength | 12 kN on the anchorage line for 3 minutes. |
| Minimum working strength | 3 kN held for 3 minutes, with less than 300 mm of slippage. A type C with a panic locking element is tested at 3 kN with 450 N on the lever. |
The maker states that the summary does not hold the full details of the standard.
Gaps in the sources
None of the sources opened uses the term figure-eight. The American ANSI Z359 pages did not open. The UIAA announcement does not print the number 129; the standards list does.
Sources
- UIAA, Safety Standards list, read October 21, 2026
- UIAA, First-ever safety standard for braking devices, June 25, 2009, read October 21, 2026
- BSI Knowledge, BS EN 341:2011 Personal fall protection equipment. Descender devices for rescue, read October 21, 2026
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, read October 21, 2026
- Edelrid, Summary of EN 12841 rope adjustment devices, read October 21, 2026