Equipment inspection frequency for climbing gear by country
OSHA words the check as every workshift. The German DGUV rule adds an expert check at least every 12 months, and the UK industry code cites 6 and 12 month examinations for lifting gear.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work. Five sources give timing: 29 CFR 1910.140 from OSHA, and DGUV Regel 112-198 of September 2019. The others are the Arboricultural Association's Industry Code of Practice for Tree Work at Height (May 2020), the SafeWork NSW Tree works Code of Practice (March 2026) and the WorkSafe New Zealand Approved Code of Practice for arboriculture (November 2012).
The sources use three levels of check. The first is a look by the user before work. The second is a closer inspection, often recorded. The third is an examination by a competent or qualified person. Each source words the intervals differently, and some give no fixed interval at all.
Frequency by country
| Source | User check | Periodic or expert check |
|---|---|---|
| United States, OSHA | Before initial use, each workshift | No fixed interval. A competent person inspects after impact loading. |
| United Kingdom, industry code | Visual and tactile check before use | Recorded inspections at set intervals. Lifting-people gear every 6 months, other lifting gear every 12 months. |
| Germany, DGUV | Visual check before every use | Competent person as needed, at least every 12 months |
| Australia, NSW code | Before and after each use | Harness inspections at least annually |
| New Zealand, approved code | Before each use | No fixed interval. Worn gear leaves service. |
United States
OSHA's rule on personal fall protection systems, paragraph (c)(18), requires inspection before initial use during each workshift. Defective components leave service. Paragraph (c)(17) covers a system or component that took impact loading. It leaves service at once and does not return until a competent person inspects it and finds it undamaged and safe for fall protection use. Paragraph (c)(6) has a competent or qualified person inspect each knot in a lanyard or vertical lifeline before any employee uses it. The rule prints no calendar interval.
United Kingdom
The Arboricultural Association code expects operators to make visual and tactile pre-use inspections. It adds recorded inspections at intervals set by the intensity of use and specified by a competent person under an examination scheme. Its glossary defines an interim inspection as a periodic check, often by the operator, with the interval based on how often the gear is used. Interim inspections commonly happen weekly or fortnightly.
The legal summary in the code covers LOLER, the lifting regulations. It lists recorded interim inspections for gear with high wear, and thorough examination by an independent competent person. Thorough examination of equipment used for lifting people falls at least every 6 months, and of other equipment such as rigging at least every 12 months. The code also says the person doing a thorough examination reports defects and keeps records.
Germany
DGUV Regel 112-198 puts the first check on the user. Section 10.3.1 has users check fall protection gear by sight before every use. Defects go to the person in charge, and work at height with the faulty gear stops. Section 10.3.2 has the employer arrange a check by a competent person according to the maker's instructions, working conditions and operating circumstances, as needed and at least every 12 months. It names a course under DGUV Grundsatz 312-906 as one route to that competence, with a certificate. Section 10.4 asks for documentation of the regular checks.
Australia and New Zealand
The NSW code, in section 4.1, says the climber should inspect climbing gear before and after each use and remove damaged gear until a competent person assesses it. Section 4.4 says harness inspections must be carried out at least annually. Prusik loops and other friction knots (4.7) get a check before and after each use. Connection hardware (4.10) gets one before, during and after use. Tree lowering equipment in section 8.3 gets the same.
The New Zealand code is dated November 2012 and was approved under section 20 of the Health and Safety in Employment Act. It requires arborists to check climbing lines, work lines, lanyards and other climbing gear for damage, cuts, abrasion and deterioration before each use. Harness components and spurs get a before-use check too. The code gives no calendar interval for any item.
Where the wording differs
Only the German rule and the NSW harness clause print a fixed 12-month figure for climbing gear, and the UK code gets its 6 and 12 month figures from LOLER for lifting equipment. OSHA and the New Zealand code tie every check to use. Related tables are in inspection intervals by item and country and gear inspection and thorough examination rules.
Sources
- OSHA, 29 CFR 1910.140, Personal fall protection systems, paragraphs (c)(6), (c)(17) and (c)(18), read October 21, 2026
- DGUV, DGUV Regel 112-198, Benutzung von persönlichen Schutzausrüstungen gegen Absturz, September 2019, section 10.3, read October 21, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, section 3.2, read October 21, 2026
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height, second edition, May 2020, sections 3.10, 3.11 and Part 4, read October 21, 2026
- SafeWork NSW, Tree works Code of practice, March 2026, sections 4.1, 4.4, 4.7, 4.10 and 8.3, read October 21, 2026