Inspection intervals for climbing gear by item and country
Each rule sets its own interval for rope, harness, lanyard, connector, descender and helmet: every shift, every use, every 6 months or every year. The table sets out five jurisdictions, item by item.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The wording below is closely restated from the OSHA rule, the WorkSafeBC regulation, the UK lifting regulations and HSE guidance, the SafeWork NSW code of practice and a New Zealand industry guide.
The rules use three different ideas. A pre-use check is the user looking at the item before work. An inspection is a closer look by a competent or qualified person. A thorough examination is a periodic, written examination. Few rules use all three words.
Interval table by item and country
North America
| Item | United States, OSHA | British Columbia, WorkSafeBC |
|---|---|---|
| Rope | Before initial use each workshift | Before first use each work shift |
| Harness | Before initial use each workshift | Before first use each work shift |
| Lanyard | Before initial use each workshift; each knot inspected before use | Before first use each work shift |
| Connector | Before initial use each workshift | Before first use each work shift |
| Descender or lowering device | Before initial use each workshift, as a system component | Before first use each work shift, as part of the system |
| Helmet | No interval given | No interval given |
United Kingdom
| Item | LOLER and HSE wording |
|---|---|
| Rope | Inspected every day; written weekly record for high-wear items such as ropes; thorough examination at the LOLER period |
| Harness | Listed as lifting equipment; thorough examination at the LOLER period |
| Lanyard | Strops are listed as lifting equipment; thorough examination at the LOLER period |
| Connector | Karabiners are listed as lifting equipment; thorough examination at the LOLER period |
| Descender or lowering device | Rigging systems for lowering branches are listed; the period depends on the kind of lifting equipment |
| Helmet | No interval given |
Australia and New Zealand
| Item | New South Wales, SafeWork NSW | New Zealand, NZ Arb guide |
|---|---|---|
| Rope | Before and after each use; removed from service when unsafe | Before each use |
| Harness | Before and after each use; inspections at least annually | Components checked before use |
| Lanyard | Before and after each use; webbing retired on any visible cut | Before each use |
| Connector | Before, during and after use | Before each use, as other climbing equipment |
| Descender or lowering device | Lowering equipment before, during and after each use | Tackle blocks, pulleys and connecting links before use |
| Helmet | PPE regularly inspected; no helmet interval given | Before use |
United States
OSHA 29 CFR 1910.140(c)(18) requires personal fall protection systems to be inspected before initial use during each workshift for mildew, wear, damage and other deterioration. Defective components must be removed from service. Paragraph (c)(19) names ropes, belts, lanyards and harnesses used for personal fall protection.
Under (c)(17), a system or component that has been impact loaded is removed from service immediately. It stays out until a competent person inspects it and finds it undamaged and safe. Under (c)(6), a competent or qualified person inspects each knot in a lanyard or vertical lifeline before any employee uses it. The text is on the OSHA 1910.140 page.
British Columbia
WorkSafeBC Part 26 defines a tree-climbing system as the equipment a person relies on for support and security while climbing, including harness, climbing lines and lanyards. Section 26.12.0.6, in force from December 1, 2021, requires inspection by a qualified arborist before the system is first used on each work shift.
Each piece is removed from service as the maker specifies or if it is defective. The whole system comes out if any piece arrests a fall. It returns only after the maker, its authorized agent or a professional engineer has inspected and certified it safe. The full wording sits in the Part 26 forestry operations text.
Section 11.9 of Part 11 on fall protection asks for inspection by a qualified person before use on each workshift. Section 26.42 asks for forestry rigging to be inspected at regular and frequent intervals by a qualified worker.
United Kingdom
LOLER regulation 9(3) sets the periods for lifting equipment exposed to conditions that cause deterioration liable to result in dangerous situations. Equipment for lifting persons, or an accessory for lifting, gets a thorough examination at least every 6 months. Other lifting equipment gets one at least every 12 months. An examination scheme is the alternative. An examination also follows each time exceptional circumstances liable to jeopardise safety have occurred.
The same paragraph adds that, if appropriate, a competent person inspects the equipment at suitable intervals between examinations. The regulation is on legislation.gov.uk, and its text is adapted here under the Open Government Licence v3.0.
Guidance from HSE, in its lifting equipment in arboriculture page lists rope access and work positioning systems, anchor points, ropes, karabiners, harnesses and strops as lifting equipment, and notes that a load includes a person. It calls for the main climbing rope and associated equipment to be inspected every day by a competent person. Arborists should be trained to make a daily pre-use check. For high-wear items such as ropes, HSE says a written weekly record of inspection should be kept. The HSE page prints no 6-month figure. That figure comes from the regulation.
New South Wales
The SafeWork NSW Tree works code of practice, which commenced on March 27, 2026, says the climber should thoroughly inspect climbing equipment before and after each use. Rope made unsafe by damage, defect or wear and tear should be removed from service. Harness inspections must be carried out at least annually. Lanyard webbing should be retired if there are any visible cuts.
Connection hardware is inspected for safe operation before, during and after use, and tree lowering equipment is inspected before, during and after each use. Prusik loops are inspected before and after each use for heat and abrasion damage. The code also asks for PPE to be regularly inspected and maintained, and says defective equipment must not be used. It names no separate helmet interval. The code is the Tree works code of practice.
New Zealand
The New Zealand Arboricultural Association publishes the guide Safety Requirements for NZ Arboricultural Operations, edition 3.1, 2022, version 2. It is an industry guide, not a WorkSafe New Zealand document. Clause 31.5 requires climbing lines, work lines, lanyards and other climbing equipment to be checked for damage, cuts, abrasion or deterioration before each use, and removed from service when excessive wear or damage shows.
Clause 30.6 asks arborists to check all harness components before use, and to retire the harness when signs of excessive wear or damage appear or the expiry date has lapsed. Clause 8.5 has helmets inspected before use and removed from service for excessive wear or damage. Otherwise they are replaced as the maker recommends.
Clause 51.2 has tackle blocks, pulleys, connecting links, chokers and slings inspected before use. The clause on logbooks ends with the printed fragment "6 monthly documented climbing equipment inspection". The full text is in the NZ Arb safety guide.
Sources
- OSHA, 29 CFR 1910.140 personal fall protection systems, read October 16, 2026
- WorkSafeBC, OHS Regulation Part 11 fall protection, read October 16, 2026
- WorkSafeBC, OHS Regulation Part 26 forestry operations, sections 26.12.0.6 and 26.42, read October 16, 2026
- HSE, lifting equipment in arboriculture, read October 16, 2026
- legislation.gov.uk, Lifting Operations and Lifting Equipment Regulations 1998, regulation 9, read October 16, 2026
- SafeWork NSW, Tree works code of practice, March 2026, read October 16, 2026
- New Zealand Arboricultural Association, Best Practice Guide for Safety Requirements in NZ Arboricultural Operations, edition 3.1, 2022, read October 16, 2026