ArbNation Join free

Elevating work platform licences and training in Australia and New Zealand: the 11 metre line and WorkSafe NZ guidance

In Australia a boom-type elevating work platform with a boom length of 11 metres or more falls under the WP high risk work licence class. New Zealand has no licence class and publishes WorkSafe guidance with NZQA unit standards.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The Australian text is SafeWork NSW's page on high risk work licences. The New Zealand text is WorkSafe NZ's good practice guideline on mobile EWPs, which it calls MEWPs. Standards Australia describes AS 2550.10:2025, the safe use standard the WorkSafe NZ guideline points to. Bucket trucks and cherry pickers are covered in bucket trucks and EWPs, and the licence picture by country is in MEWP operator licences by country.

Australia: the WP licence class

SafeWork NSW lists the boom-type EWP class as WP. The class covers a telescoping, hinged or articulated device, or any combination, that carries a platform for people, equipment and materials, where the boom length is 11 metres or more. SafeWork NSW gives two ways to measure the boom and says to use the longer result.

MeasurementHow SafeWork NSW describes it
VerticalFrom the surface supporting the platform to the floor of the platform, with the platform extended to its maximum height
HorizontalFrom the centre point of the boom's rotation to the outer edge of the platform, with the platform extended to its maximum distance

A telehandler fitted with a personnel box that has operating controls in the box falls under the class when its boom length is 11 metres or more. WP sits with the materials hoist (HM) and the personnel and materials hoist (HP) as one of three hoist classes. SafeWork NSW counts 29 classes of high risk work in all.

Australia: licence rules on the NSW page

SafeWork NSW says that as a rule, in Australia, high risk work done on residential, commercial or industrial sites calls for a licence whatever the cost or size of the work. Work done while training for a class, under the supervision of a licence holder, is the exception it names. The employer or manager must provide direct supervision, unless the task makes that impractical or unnecessary and the lower level of supervision puts no one at risk.

ItemSafeWork NSW
Minimum ageAt least 18 to apply
Training and assessmentTraining with a registered training organisation, then assessment as competent by a SafeWork NSW accredited assessor
LanguageAble to speak English well enough to do the work safely with other people
Licence term5 years; a class added later expires with the licence
RenewalUp to 12 months after expiry, after which training and assessment start again
ReminderAn email or text message about 60 days before expiry

The NSW page also says an application for renewal lodged before expiry lets the holder keep working until the confirmation arrives. SafeWork NSW adds that a high risk work licence must be issued by the state or territory where the holder usually lives.

Australia: AS 2550.10:2025

Standards Australia published a spotlight on AS 2550.10:2025, part 10 of the cranes, hoists and winches safe use series, on April 28, 2025. It outlines safe systems of work, management, planning, selection, operation and maintenance of MEWPs. It applies to MEWPs designed and built to AS/NZS 1418.10 and can be used for similar equipment with no safe use standard of its own. The 2025 edition gives more definitive guidance on fall arrest systems, leaving a platform up and travelling with it up. Maintenance requirements for insulated MEWPs from AS/NZS 1418.10 are incorporated into its Appendix C. The standard defines the competent person for supervising, inspecting, maintaining and operating a MEWP.

New Zealand: the WorkSafe guideline

WorkSafe NZ states that its MEWP guideline has not been updated for the Health and Safety at Work Act 2015 and its regulations. The text was written under the Health and Safety in Employment Act 1992. WorkSafe NZ adds that it may still hold relevant practice and is to be read with industry standards, and that the guidance will be reviewed and either updated, replaced or revoked. A clarification notice dated August 2014 sits on the page.

The guideline applies to platforms raised by scissor mechanisms, telescoping boom or tower, articulation or a mix of these. It names arboriculture and the bush and forest industries among the users. It excludes forklifts with platforms, platforms hung from crane hooks, suspended scaffolds, lifts and elevators, telehandlers not set up as a MEWP, and what it calls horticultural MEWPs, which have their own guideline.

New Zealand: training and inspection figures

The guideline puts the duty on the employer or principal. The operator is to be trained by a competent person on the type of MEWP in use, and supervised until judged competent. It defines a competent person as someone who has demonstrated competency on a particular MEWP type, and gives NZQA unit standards as one way to show it.

NZQA unit standardTitle in the guideline
23966Describe types of EWPs and legislative requirements for their use, taken before 23960 through 23964
23960Assess the worksite, prepare and operate a scissor lift EWP
23961Assess the worksite, prepare and operate a truck mounted EWP
23962Assess the worksite, prepare and operate a self-propelled boom lift EWP
23963Assess the worksite, prepare and operate a trailer mounted EWP
23964Assess the worksite, prepare and operate a vertical lift EWP
17259Operate an elevated work platform vehicle for arboriculture

The guideline says any course must cover AS 2550.10 and that refresher training should not be more than three years apart. Routine inspections by the owner, hirer and supplier come at least every 3 months. A competent person examines the MEWP at least every 6 months and after an accident or major repair. A fibreglass boom gets an acoustic emission test at least every 24 months.

Sources