Felling cuts and hazards: the regulator wording in OSHA, HSE, NSW and NZ side by side
OSHA 1910.266, the British FISA 302 guide and HSE, the SafeWork NSW tree works code and the New Zealand arboriculture code word the undercut, scarf, hinge, escape route and two tree lengths rules in different ways.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work. Five texts are set side by side. They are the US logging standard 29 CFR 1910.266, the SafeWork NSW Tree work Code of Practice and the WorkSafe New Zealand Approved Code of Practice for Safety and Health in Arboriculture. The other two are HSE's chainsaw and tree felling page and FISA Safety Guide 302, updated June 2018. FISA is the British forest industry body.
The first cut: undercut, scarf or sink cut
| Body | Wording |
|---|---|
| OSHA 1910.266(h)(2) | Calls it the undercut. One is made in each tree felled unless the employer shows that felling without one creates no hazard. It is sized so the tree will not split and will fall in the intended direction. |
| HSE | Calls it the directional or sink cut. Control of the fell comes from a combination of that cut, the hinge and the main felling or back cut. Cuts must suit the tree size and form and be consistently accurate. |
| FISA 302 | Calls it the sink cut. The guide says always make one. The two cuts forming it are aligned to the felling direction, meet exactly so the hinge is not weakened, and suit the species, terrain, work system, site and weather. |
| SafeWork NSW | Calls it the scarf. Chapter 9 says a scarf and back-cut should be used in felling trees. Its figure shows a 45 degree scarf. |
| WorkSafe NZ | Calls it the scarf. Scarf cuts shall be used on all trees and trunks over 125 mm diameter at breast height. The two cuts shall not cross where they meet. The scarf should be 45 degrees or more and its depth should not exceed one third of the tree diameter. It may be conventional, open-face or Humboldt. |
The back cut and the hinge
| Body | Wording |
|---|---|
| OSHA 1910.266(h)(2) | A backcut is made in each tree. It leaves enough hinge wood to hold the tree to the stump during most of its fall, so the hinge guides the fall. It sits above the horizontal facecut to give a platform that prevents kickback. The exception is tree pulling operations, where it may be at or below the facecut. |
| HSE | HSE lists free-hand pulling as something to avoid. If the person on the rope sways or rocks the tree, the main felling cut at the rear of the tree will open and close, and the operator could compromise the hinge. Over tensioned lines may cause the hinge to sever prematurely and the tree to split. |
| FISA 302 | The main felling cut is at or slightly above the level of the horizontal sink cut. An appropriately sized parallel-sided hinge is left at right angles to the direction of fall. Where rot is found or suspected, cuts, hinge size and felling height are adjusted. |
| SafeWork NSW | The back cut is slightly above the scarf horizontal. The figure labels the wood left between the cuts as holding wood. |
| WorkSafe NZ | Scarf and back cuts are made at a height above the highest ground level. The back cut shall not penetrate into the predetermined hinge area. When felling starts, the scarf and back cut are completed before the next tree is started. |
Distance from the tree being felled
| Body | Wording |
|---|---|
| OSHA 1910.266(h) | Adjacent occupied work areas are at least two tree lengths of the trees being felled apart. The distance reflects slope, growth density, tree height and soil structure. It is greater than two tree lengths on a slope where rolling or sliding is foreseeable. When a spring pole or tree under stress is cut, no one but the feller is closer than two tree lengths. |
| FISA 302 | Felling is a one-person operation and a safe working distance of two tree lengths is held unless exceptional conditions and a comprehensive risk assessment dictate otherwise. Near overhead power lines the clearance is not less than twice the height of the trees. |
| SafeWork NSW | Clear felling is "generally used" where there is a minimum of two tree lengths of open space in all directions from the base. Controlled directional felling is used where space is under two tree lengths, with ropes, cables or mobile plant. |
| WorkSafe NZ | People not assisting the felling stay at least two tree-lengths from the tree. No machine operates within two treelengths of a felling operation. |
| HSE | HSE prints no tree-length distance. Its key lessons cover site survey, work planning, felling cuts, felling aids and escape routes. |
Escape routes and hung trees
| Body | Wording |
|---|---|
| OSHA 1910.266(h)(2) | The feller plans and clears a retreat path before felling. It runs diagonally away from the expected felling line unless that is a greater hazard. After the backcut, the feller moves a safe distance away at once. |
| HSE | Escape routes are planned in advance and must be clear of obstructions. If control of the fell is lost, HSE calls for using the route and trying not to turn one's back on the falling tree. |
| SafeWork NSW | The 45 degree escape route extends to an area at least 6 metres from the stump, with standing vegetation removed to give a clear gap. |
| WorkSafe NZ | The ideal escape route is 45 degrees on either side of a line drawn opposite the intended fall. A hung-up tree shall be brought to the ground as soon as possible, and no one moves within two treelengths of its fall direction. |
Where two of these bodies give different figures, each is printed as its own text gives it. OSHA's logging standard is written for logging sites, and the others are written for tree work.
Sources
- eCFR, 29 CFR 1910.266 Logging operations, paragraph (h) felling and bucking, read October 16, 2026
- HSE, Chainsaws and tree felling: key lessons (chainsaw operator page), read October 16, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, sections 3.4.2 and 3.4.3, read October 16, 2026
- UK Forest Industry Safety Accord, FISA Safety Guide 302 Basic chainsaw felling and manual takedown, updated June 2018, read October 16, 2026
- SafeWork NSW, Tree work Code of Practice, chapter 9 felling, read October 16, 2026